This version (27 Mar 2023 12:34) was approved by Alin-Tudor Sferle.The Previously approved version (02 Jan 2023 21:35) is available.

AD7606X HDL Reference Design

Introduction

The EVAL-AD7606B-FMCZ and EVAL-AD7606C-18 evaluation boards are designed to help users to easily evaluate the features of AD7606B, AD7606C-16 and AD7606C-18 analog-to-digital converters (ADCs).

Used devices

Evaluation board

Supported FPGA carrier

ZEDBOARD

Reference HDL Design

The design is built upon ADI's generic HDL reference design framework. In the ADI Reference Designs HDL User Guide can be found an in-depth presentation and instructions about the HDL design framework in general.

Block diagram

AD7606X_FMC using the PARALLEL interface

Required software

We're upgrading the Xilinx tools on every release. The supported version number can be found in our git repository .
An UART terminal (Tera Term/Hyperterminal), baud rate set to 115200.

Parameters

Parameter name	Default value	Description
DEV_CONFIG	0	Device that will be used: 0 - AD7606B, 1 - AD7606C-16, 2 - AD7606C-18
SIMPLE_STATUS_CRC	0	ADC Read Mode options: 0 - Simple, 1 - STATUS, 2 - CRC, 3 - STATUS_CRC
EXT_CLK	0	External clock option for the ADC clock: No(0), Yes(1)

Using the HDL reference design

In the ADI Reference Designs HDL User Guide can be found an in-depth presentation and instructions about the HDL design in general.

In the axi_ad7606x's wiki page, can be found a detailed description of the core.

The data path of the HDL design is simple as follows:

the parallel interface is controlled by the axi_ad7606x IP core
the serial interface is controlled by the SPI Engine Framework
data is written into memory by a DMA (axi_dmac core)
all the control pins of the device are driven by GPIO's

In order to build the HDL design the user has to go through the following steps:

Confirm that you have the right tools (see Release notes)
Clone the HDL GitHub repository (see https://wiki.analog.com/resources/fpga/docs/git)
Choose the required interface (see caption Switching between interface types)
Build the project (see https://wiki.analog.com/resources/fpga/docs/build)

Switching between device types, operation modes and clocking option

Before the board power-up, the user has to choose the device type, operation mode and clocking option. Depending on the operation mode, some hardware modifications need to be done on the board and/or Tcl script:

In case of the AD7606C-16 device:

$ make DEV_CONFIG=1

In case of the STATUS operation mode:

$ make SIMPLE_STATUS_CRC=1

PL Interrupts

Instance	HDL interrupt	Linux PsU interrupt
—	0	89
—	1	90
—	2	91
—	3	92
—	4	93
—	5	94
—	6	95
—	7	96
—	8	104
—	9	105
—	10	106
—	11	107
—	12	108
axi_ad7606x_dma	13	109
—	14	110
—	15	111

GPIO signals

Ps7 EMIO offset = 54

GPIO Signal	GPIO	HDL GPIO EMIOn
adc_serpar	93	39
adc_refsel	92	38
adc_reset	91	37
adc_stby	90	36
adc_range	89-87	35
adc_os	86	34-32

Register Map

The register map of the core contains instances of three generic register maps: Base, ADC common and ADC channel. The following table presents the base addresses of each instance, after that can be found the detailed description of each generic register map. The absolute address of a register should be calculated by adding the instance base address to the registers relative address.

Base (common to all cores)

Click to expand regmap

0x0000	0x0000	REG_VERSION				Version and Scratch Registers
Address		Bits	Name	Type	Default	Description
DWORD	BYTE	Bits	Name	Type	Default	Description
		[31:0]	VERSION[31:0]	RO	0x00000000	Version number. Unique to all cores.
0x0001	0x0004	REG_ID				Version and Scratch Registers
		[31:0]	ID[31:0]	RO	0x00000000	Instance identifier number.
0x0002	0x0008	REG_SCRATCH				Version and Scratch Registers
		[31:0]	SCRATCH[31:0]	RW	0x00000000	Scratch register.
0x0003	0x000c	REG_CONFIG				Version and Scratch Registers
		[0]	IQCORRECTION_DISABLE	RO	0x0	If set, indicates that the IQ Correction module was not implemented. (as a result of a configuration of the IP instance)
		[1]	DCFILTER_DISABLE	RO	0x0	If set, indicates that the DC Filter module was not implemented. (as a result of a configuration of the IP instance)
		[2]	DATAFORMAT_DISABLE	RO	0x0	If set, indicates that the Data Format module was not implemented. (as a result of a configuration of the IP instance)
		[3]	USERPORTS_DISABLE	RO	0x0	If set, indicates that the logic related to the User Data Format (e.g. decimation) was not implemented. (as a result of a configuration of the IP instance)
		[4]	MODE_1R1T	RO	0x0	If set, indicates that the core was implemented in 1 channel mode. (e.g. refer to AD9361 data sheet)
		[5]	DELAY_CONTROL_DISABLE	RO	0x0	If set, indicates that the delay control is disabled for this IP. (as a result of a configuration of the IP instance)
		[6]	DDS_DISABLE	RO	0x0	If set, indicates that the DDS is disabled for this IP. (as a result of a configuration of the IP instance)
		[7]	CMOS_OR_LVDS_N	RO	0x0	CMOS or LVDS mode is used for the interface. (as a result of a configuration of the IP instance)
		[8]	PPS_RECEIVER_ENABLE	RO	0x0	If set, indicates the PPS receiver is enabled. (as a result of a configuration of the IP instance)
		[9]	SCALECORRECTION_ONLY	RO	0x0	If set, indicates that the IQ Correction module implements only scale correction. IQ correction must be enabled. (as a result of a configuration of the IP instance)
		[12]	EXT_SYNC	RO	0x0	If set the transport layer cores (ADC/DAC) have implemented the support for external synchronization signal.
		[13]	RD_RAW_DATA	RO	0x0	If set, the ADC has the capability to read raw data in register REG_CHAN_RAW_DATA from adc_channel.
0x0004	0x0010	REG_PPS_IRQ_MASK				PPS Interrupt mask
		[0]	PPS_IRQ_MASK	RW	0x1	Mask bit for the 1PPS receiver interrupt
0x0007	0x001c	REG_FPGA_INFO				FPGA device information Intel encoded values Xilinx encoded values
		[31:24]	FPGA_TECHNOLOGY	RO	0x0	Encoded value describing the technology/generation of the FPGA device (arria 10/7series)
		[23:16]	FPGA_FAMILY	RO	0x0	Encoded value describing the family variant of the FPGA device(e.g., SX, GX, GT or zynq, kintex, virtex)
		[15:8]	SPEED_GRADE	RO	0x0	Encoded value describing the FPGA's speed-grade
		[7:0]	DEV_PACKAGE	RO	0x0	Encoded value describing the device package. The package might affect high-speed interfaces
Tue Mar 14 10:17:59 2023

ADC Common (axi_ad*)

Click to expand regmap

0x0010	0x0040	REG_RSTN				ADC Interface Control & Status
Address		Bits	Name	Type	Default	Description
DWORD	BYTE	Bits	Name	Type	Default	Description
		[2]	CE_N	RW	0x0	Clock enable, default is enabled(0x0). An inverse version of the signal is exported out of the module to control clock enables
		[1]	MMCM_RSTN	RW	0x0	MMCM reset only (required for DRP access). Reset, default is IN-RESET (0x0), software must write 0x1 to bring up the core.
		[0]	RSTN	RW	0x0	Reset, default is IN-RESET (0x0), software must write 0x1 to bring up the core.
0x0011	0x0044	REG_CNTRL				ADC Interface Control & Status
		[16]	SDR_DDR_N	RW	0x0	Interface type (1 represents SDR, 0 represents DDR)
		[15]	SYMB_OP	RW	0x0	Select symbol data format mode (0x1)
		[14]	SYMB_8_16B	RW	0x0	Select number of bits for symbol format mode (1 represents 8b, 0 represents 16b)
		[12:8]	NUM_LANES[4:0]	RW	0x0	Number of active lanes (1 : CSSI 1-lane, LSSI 1-lane, 2 : LSSI 2-lane, 4 : CSSI 4-lane). For AD7768, AD7768-4 and AD777x number of active lanes : 1/2/4/8 where supported.
		[3]	SYNC	RW	0x0	Initialize synchronization between multiple ADCs
		[2]	R1_MODE	RW	0x0	Select number of RF channels 1 (0x1) or 2 (0x0).
		[1]	DDR_EDGESEL	RW	0x0	Select rising edge (0x0) or falling edge (0x1) for the first part of a sample (if applicable) followed by the successive edges for the remaining parts. This only controls how the sample is delineated from the incoming data post DDR registers.
		[0]	PIN_MODE	RW	0x0	Select interface pin mode to be clock multiplexed (0x1) or pin multiplexed (0x0). In clock multiplexed mode, samples are received on alternative clock edges. In pin multiplexed mode, samples are interleaved or grouped on the pins at the same clock edge.
0x0012	0x0048	REG_CNTRL_2				ADC Interface Control & Status
		[1]	EXT_SYNC_ARM	RW	0x0	Setting this bit will arm the trigger mechanism sensitive to an external sync signal. Once the external sync signal goes high it synchronizes channels within a ADC, and across multiple instances. This bit has an effect only the EXT_SYNC synthesis parameter is set. This bit self clears.
		[2]	EXT_SYNC_DISARM	RW	0x0	Setting this bit will disarm the trigger mechanism sensitive to an external sync signal. This bit has an effect only the EXT_SYNC synthesis parameter is set. This bit self clears.
		[8]	MANUAL_SYNC_REQUEST	RW	0x0	Setting this bit will issue an external sync event if it is hooked up inside the fabric. This bit has an effect only the EXT_SYNC synthesis parameter is set. This bit self clears.
0x0013	0x004c	REG_CNTRL_3				ADC Interface Control & Status
		[8]	CRC_EN	RW	0x0	Setting this bit will enable the CRC generation.
		[7:0]	CUSTOM_CONTROL	RW	0x00	ADAQ8092 Select output format decode mode. - bit [0] - enables digital output randomizer decode - bit [1] - enables alternate bit polarity decode AD4858 Select data format/oversampling - bit [2] - enable oversampling - bits [1:0] packet format selection: 0 = 20 bit 1 = 24 bit 2 = 32 bit 3 = 32 bit AD7606X_PI Select the parallel interface's operation mode - bit [2] - change mode with the selected one - bits [1:0] - requested operation mode: 0 = SIMPLE 1 = CRC_ENABLED 2 = STATUS_HEADER 3 = CRC_STATUS 07 Mar 2023 17:38 · Andrei Grozav
0x0015	0x0054	REG_CLK_FREQ				ADC Interface Control & Status
		[31:0]	CLK_FREQ[31:0]	RO	0x0000	Interface clock frequency. This is relative to the processor clock and in many cases is 100MHz. The number is represented as unsigned 16.16 format. Assuming a 100MHz processor clock the minimum is 1.523kHz and maximum is 6.554THz. The actual interface clock is CLK_FREQ * CLK_RATIO (see below). Note that the actual sampling clock may not be the same as the interface clock- software must consider device specific implementation parameters to calculate the final sampling clock.
0x0016	0x0058	REG_CLK_RATIO				ADC Interface Control & Status
		[31:0]	CLK_RATIO[31:0]	RO	0x0000	Interface clock ratio - as a factor actual received clock. This is implementation specific and depends on any serial to parallel conversion and interface type (ddr/sdr/qdr).
0x0017	0x005c	REG_STATUS				ADC Interface Control & Status
		[4]	ADC_CTRL_STATUS	RO	0x0	If set, indicates that the device's register data is available on the data bus.
		[3]	PN_ERR	RO	0x0	If set, indicates pn error in one or more channels.
		[2]	PN_OOS	RO	0x0	If set, indicates pn oos in one or more channels.
		[1]	OVER_RANGE	RO	0x0	If set, indicates over range in one or more channels.
		[0]	STATUS	RO	0x0	Interface status, if set indicates no errors. If not set, there are errors, software may try resetting the cores.
0x0018	0x0060	REG_DELAY_CNTRL				ADC Interface Control & Status(`Deprecated from version 9`)
		[17]	DELAY_SEL	RW	0x0	Delay select, a 0x0 to 0x1 transition in this register initiates a delay access controlled by the registers below.
		[16]	DELAY_RWN	RW	0x0	Delay read (0x1) or write (0x0), the delay is accessed directly (no increment or decrement) with an address corresponding to each pin, and data corresponding to the total delay.
		[15:8]	DELAY_ADDRESS[7:0]	RW	0x00	Delay address, the range depends on the interface pins, data pins are usually at the lower range.
		[4:0]	DELAY_WDATA[4:0]	RW	0x0	Delay write data, a value of 1 corresponds to (1/200)ns for most devices.
0x0019	0x0064	REG_DELAY_STATUS				ADC Interface Control & Status(`Deprecated from version 9`)
		[9]	DELAY_LOCKED	RO	0x0	Indicates delay locked (0x1) state. If this bit is read 0x0, delay control has failed to calibrate the elements.
		[8]	DELAY_STATUS	RO	0x0	If set, indicates busy status (access pending). The read data may not be valid if this bit is set.
		[4:0]	DELAY_RDATA[4:0]	RO	0x0	Delay read data, current delay value in the elements
0x001A	0x0068	REG_SYNC_STATUS				ADC Synchronization Status register
		[0]	ADC_SYNC	RO	0x0	ADC synchronization status. Will be set to 1 after the synchronization has been completed or while waiting for the synchronization signal in JESD204 systems.
0x001C	0x0070	REG_DRP_CNTRL				ADC Interface Control & Status
		[28]	DRP_RWN	RW	0x0	DRP read (0x1) or write (0x0) select (does not include GTX lanes). NOT-APPLICABLE if DRP_DISABLE is set (0x1).
		[27:16]	DRP_ADDRESS[11:0]	RW	0x00	DRP address, designs that contain more than one DRP accessible primitives have selects based on the most significant bits (does not include GTX lanes). NOT-APPLICABLE if DRP_DISABLE is set (0x1).
		[15:0]	RESERVED[15:0]	RO	0x0000	Reserved for backward compatibility.
0x001D	0x0074	REG_DRP_STATUS				ADC Interface Control & Status
		[17]	DRP_LOCKED	RO	0x0	If set indicates that the DRP has been locked.
		[16]	DRP_STATUS	RO	0x0	If set indicates busy (access pending). The read data may not be valid if this bit is set (does not include GTX lanes). NOT-APPLICABLE if DRP_DISABLE is set (0x1).
		[15:0]	RESERVED[15:0]	RO	0x00	Reserved for backward compatibility.
0x001E	0x0078	REG_DRP_WDATA				ADC DRP Write Data
		[15:0]	DRP_WDATA[15:0]	RW	0x00	DRP write data (does not include GTX lanes). NOT-APPLICABLE if DRP_DISABLE is set (0x1).
0x001F	0x007c	REG_DRP_RDATA				ADC DRP Read Data
		[15:0]	DRP_RDATA[15:0]	RO	0x00	DRP read data (does not include GTX lanes).
0x0020	0x0080	REG_ADC_CONFIG_WR				ADC Write Configuration Data
		[31:0]	ADC_CONFIG_WR[31:0]	RW	0x0000	Custom Write to the available registers.
0x0021	0x0084	REG_ADC_CONFIG_RD				ADC Read Configuration Data
		[31:0]	ADC_CONFIG_RD[31:0]	RO	0x0000	Custom read of the available registers.
0x0022	0x0088	REG_UI_STATUS				User Interface Status
		[2]	UI_OVF	RW1C	0x0	User Interface overflow. If set, indicates an overflow occurred during data transfer at the user interface (FIFO interface). Software must write a 0x1 to clear this register bit.
		[1]	UI_UNF	RW1C	0x0	User Interface underflow. If set, indicates an underflow occurred during data transfer at the user interface (FIFO interface). Software must write a 0x1 to clear this register bit.
		[0]	UI_RESERVED	RW1C	0x0	Reserved for backward compatibility.
0x0023	0x008c	REG_ADC_CONFIG_CTRL				ADC RD/WR configuration
		[31:0]	ADC_CONFIG_CTRL[31:0]	RW	0x0000	Control RD/WR requests to the device's register map: bit 1 - RD ('b1) , WR ('b0), bit 0 - enable WR/RD operation.
0x0028	0x00a0	REG_USR_CNTRL_1				ADC Interface Control & Status
		[7:0]	USR_CHANMAX[7:0]	RW	0x00	This indicates the maximum number of inputs for the channel data multiplexers. User may add different processing modules post data capture as another input to this common multiplexer. NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
0x0029	0x00a4	REG_ADC_START_CODE				ADC Synchronization start word
		[31:0]	ADC_START_CODE[31:0]	RW	0x00000000	This sets the startcode that is used by the ADCs for synchronization NOT-APPLICABLE if START_CODE_DISABLE is set (0x1).
0x002E	0x00b8	REG_ADC_GPIO_IN				ADC GPIO inputs
		[31:0]	ADC_GPIO_IN[31:0]	RO	0x00000000	This reads auxiliary GPI pins of the ADC core
0x002F	0x00bc	REG_ADC_GPIO_OUT				ADC GPIO outputs
		[31:0]	ADC_GPIO_OUT[31:0]	RW	0x00000000	This controls auxiliary GPO pins of the ADC core NOT-APPLICABLE if GPIO_DISABLE is set (0x1).
0x0030	0x00c0	REG_PPS_COUNTER				PPS Counter register
		[31:0]	PPS_COUNTER[31:0]	RO	0x00000000	Counts the core clock cycles (can be a device clock or interface clock) between two 1PPS pulse.
0x0031	0x00c4	REG_PPS_STATUS				PPS Status register
		[0]	PPS_STATUS	RO	0x0	If this bit is asserted there is no incomming 1PPS signal. Maybe the source is out of sync or it's not active.
Fri Aug 11 18:29:53 2023

ADC Channel (axi_ad*)

Click to expand regmap

0x0100	0x0400	REG_CHAN_CNTRL				ADC Interface Control & Status
Address		Bits	Name	Type	Default	Description
DWORD	BYTE	Bits	Name	Type	Default	Description
		[11]	ADC_LB_OWR	RW	0x0	If set, forces ADC_DATA_SEL to 1, enabling data loopback
		[10]	ADC_PN_SEL_OWR	RW	0x0	If set, forces ADC_PN_SEL to 0x9, device specific pn (e.g. ad9361) If both ADC_PN_TYPE_OWR and ADC_PN_SEL_OWR are set, they are ignored
		[9]	IQCOR_ENB	RW	0x0	if set, enables IQ correction or scale correction. NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
		[8]	DCFILT_ENB	RW	0x0	if set, enables DC filter (to disable DC offset, set offset value to 0x0). NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
		[6]	FORMAT_SIGNEXT	RW	0x0	if set, enables sign extension (applicable only in 2's complement mode). The data is always sign extended to the nearest byte boundary. NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
		[5]	FORMAT_TYPE	RW	0x0	Select offset binary (0x1) or 2's complement (0x0) data type. This sets the incoming data type and is required by the post processing modules for any data conversion. NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
		[4]	FORMAT_ENABLE	RW	0x0	Enable data format conversion (see register bits above). NOT-APPLICABLE if DATAFORMAT_DISABLE is set (0x1).
		[3]	RESERVED	RO	0x0	Reserved for backward compatibility.
		[2]	RESERVED	RO	0x0	Reserved for backward compatibility.
		[1]	ADC_PN_TYPE_OWR	RW	0x0	If set, forces ADC_PN_SEL to 0x1, modified pn23 If both ADC_PN_TYPE_OWR and ADC_PN_SEL_OWR are set, they are ignored
		[0]	ENABLE	RW	0x0	If set, enables channel. A 0x0 to 0x1 transition transfers all the control signals to the respective channel processing module. If a channel is part of a complex signal (I/Q), even channel is the master and the odd channel is the slave. Though a single control is used, both must be individually selected.
0x0101	0x0404	REG_CHAN_STATUS				ADC Interface Control & Status
		[12]	CRC_ERR	RW1C	0x0	CRC errors. If set, indicates CRC error. Software must first clear this bit before initiating a transfer and monitor afterwards.
		[11:4]	STATUS_HEADER	RO	0x00	The status header sent by the ADC.(compatible with AD7768/AD7768-4/AD777x).
		[2]	PN_ERR	RW1C	0x0	PN errors. If set, indicates spurious mismatches in sync state. This bit is cleared if OOS is set and is only indicates errors when OOS is cleared.
		[1]	PN_OOS	RW1C	0x0	PN Out Of Sync. If set, indicates an OOS status. OOS is set, if 64 consecutive patterns mismatch from the expected pattern. It is cleared, when 16 consecutive patterns match the expected pattern.
		[0]	OVER_RANGE	RW1C	0x0	If set, indicates over range. Note that over range is independent of the data path, it indicates an over range over a data transfer period. Software must first clear this bit before initiating a transfer and monitor afterwards.
0x0102	0x0408	REG_CHAN_RAW_DATA				ADC Raw Data Reading
		[31:0]	ADC_READ_DATA[31:0]	RO	0x0000	Raw data read from the ADC.
0x0104	0x0410	REG_CHAN_CNTRL_1				ADC Interface Control & Status
		[31:16]	DCFILT_OFFSET[15:0]	RW	0x0000	DC removal (if equipped) offset. This is a 2's complement number added to the incoming data to remove a known DC offset. NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
		[15:0]	DCFILT_COEFF[15:0]	RW	0x0000	DC removal filter (if equipped) coefficient. The format is 1.1.14 (sign, integer and fractional bits). NOT-APPLICABLE if DCFILTER_DISABLE is set (0x1).
0x0105	0x0414	REG_CHAN_CNTRL_2				ADC Interface Control & Status
		[31:16]	IQCOR_COEFF_1[15:0]	RW	0x0000	IQ correction (if equipped) coefficient. If scale & offset is implemented, this is the scale value and the format is 1.1.14 (sign, integer and fractional bits). If matrix multiplication is used, this is the channel I coefficient and the format is 1.1.14 (sign, integer and fractional bits). If SCALECORRECTION_ONLY is set, this implements the scale value correction for the current channel with the format 1.1.14 (sign, integer and fractional bits). NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
		[15:0]	IQCOR_COEFF_2[15:0]	RW	0x0000	IQ correction (if equipped) coefficient. If scale & offset is implemented, this is the offset value and the format is 2's complement. If matrix multiplication is used, this is the channel Q coefficient and the format is 1.1.14 (sign, integer and fractional bits). NOT-APPLICABLE if IQCORRECTION_DISABLE is set (0x1).
0x0106	0x0418	REG_CHAN_CNTRL_3				ADC Interface Control & Status
		[19:16]	ADC_PN_SEL[3:0]	RW	0x0	Selects the PN monitor sequence type (available only if ADC supports it). - 0x0: pn9a (device specific, modified pn9) - 0x1: pn23a (device specific, modified pn23) - 0x4: pn7 (standard O.150) - 0x5: pn15 (standard O.150) - 0x6: pn23 (standard O.150) - 0x7: pn31 (standard O.150) - 0x9: pnX (device specific, e.g. ad9361) - 0x0A: Nibble ramp (Device specific e.g. adrv9001) - 0x0B: 16 bit ramp (Device specific e.g. adrv9001)
		[3:0]	ADC_DATA_SEL[3:0]	RW	0x0	Selects the data source to DMA. 0x0: input data (ADC) 0x1: loopback data (DAC)
0x0108	0x0420	REG_CHAN_USR_CNTRL_1				ADC Interface Control & Status
		[25]	USR_DATATYPE_BE	RO	0x0	The user data type format- if set, indicates big endian (default is little endian). NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
		[24]	USR_DATATYPE_SIGNED	RO	0x0	The user data type format- if set, indicates signed (2's complement) data (default is unsigned). NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
		[23:16]	USR_DATATYPE_SHIFT[7:0]	RO	0x00	The user data type format- the amount of right shift for actual samples within the total number of bits. NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
		[15:8]	USR_DATATYPE_TOTAL_BITS[7:0]	RO	0x00	The user data type format- number of total bits used for a sample. The total number of bits must be an integer multiple of 8 (byte aligned). NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
		[7:0]	USR_DATATYPE_BITS[7:0]	RO	0x00	The user data type format- number of bits in a sample. This indicates the actual sample data bits. NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
0x0109	0x0424	REG_CHAN_USR_CNTRL_2				ADC Interface Control & Status
		[31:16]	USR_DECIMATION_M[15:0]	RW	0x0000	This holds the user decimation M value of the channel that is currently being selected on the multiplexer above. The total decimation factor is of the form M/N. NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
		[15:0]	USR_DECIMATION_N[15:0]	RW	0x0000	This holds the user decimation N value of the channel that is currently being selected on the multiplexer above. The total decimation factor is of the form M/N. NOT-APPLICABLE if USERPORTS_DISABLE is set (0x1).
0x0110	0x0440	REG_*				Channel 1, similar to register 0x100 to 0x10f.
0x0120	0x0480	REG_*				Channel 2, similar to register 0x100 to 0x10f.
0x01F0	0x07c0	REG_*				Channel 15, similar to register 0x100 to 0x10f.
Tue Mar 14 10:17:59 2023

HDL Downloads

AD7606X-FMC HDL Project.

Support

Questions? Feel free to ask your questions in EngineerZone support forums.

Wiki

Analog Devices Wiki

Table of Contents

AD7606X HDL Reference Design

Introduction

Used devices

Evaluation board

Supported FPGA carrier

Reference HDL Design

Block diagram

Required software

Parameters

Using the HDL reference design

Switching between device types, operation modes and clocking option

PL Interrupts

GPIO signals

Register Map

Base (common to all cores)

ADC Common (axi_ad*)

ADAQ8092

AD4858

AD7606X_PI

ADC Channel (axi_ad*)

HDL Downloads

Support

Analog Devices Wiki

Table of Contents

AD7606X HDL Reference Design

Introduction

Used devices

Evaluation board

Supported FPGA carrier

Reference HDL Design

Block diagram

Required software

Parameters

Using the HDL reference design

Switching between device types, operation modes and clocking option

PL Interrupts

GPIO signals

Register Map

Base (common to all cores)

ADC Common (axi_ad*)

ADAQ8092

AD4858

AD7606X_PI

ADC Channel (axi_ad*)

HDL Downloads

Support

Page Tools