Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:ad-fmcomms11-ebz:hardware [14 Feb 2019 02:53] – [Downloads] erbe reytaresources:eval:user-guides:ad-fmcomms11-ebz:hardware [09 Mar 2023 02:43] (current) – updated the design files download link Joyce Velasco
Line 2: Line 2:
 ====== AD-FMCOMMS11-EBZ Hardware ====== ====== AD-FMCOMMS11-EBZ Hardware ======
  
-===== Downloads =====  +===== Schematic, PCB Layout, Bill of Materials ===== 
 <WRAP round download> <WRAP round download>
-  * {{:resources:eval:user-guides:ad-fmcomms5-ebz:fmcomms5_schematic.pdf|Rev B schematic}} +[[adi>media/en/reference-design-documentation/design-integration-files/ad-fmcomms11-ebz-designsupport.zip|AD-FMCOMMS5-EBZ Design & Integration Files]] 
-  * {{:resources:eval:user-guides:ad-fmcomms5-ebz:fmcomms5-bom.xls|Rev B BOM}} +  * Schematic 
-  * {{:resources:eval:user-guides:ad-fmcomms5-ebz:fmcomms5_build.zip|Rev B Build Files}}+  * PCB Layout 
 +  * Bill of Materials 
 +  * Allegro Project (get the [[https://www.cadence.com/en_US/home/tools/pcb-design-and-analysis/allegro-downloads-start.html|Allegro FREE Physical Viewer]]; you need 16.5 or higher). 
 +</WRAP> 
 + 
 +===== Picture and Main components ===== 
 + 
 +==== Top Layer Main components ==== 
 + 
 +{{ :resources:eval:user-guides:ad-fmcomms11-ebz:top_view_ic_component.jpg |}} 
 +==== Bottom Layer Main components ==== 
 +{{ :resources:eval:user-guides:ad-fmcomms11-ebz:bottom_view_ic_component.jpg |}} 
 + 
 +===== Outline =====
  
-  * {{:resources:eval:user-guides:ad-fmcomms5-ebz:fmcomms5_revb.7z|Rev B Allegro Board File}} (This file is [[http://www.7-zip.org/7z.html|compressed]]). Get the [[http://www.cadence.com/products/pcb/Pages/downloads.aspx|Allegro FREE Physical Viewer]] (You need 16.5 or higher).+For those that don't want to load up the Allegro viewer, here is a basic outline/component placements of the board.  The PCB measures 100mm x 62mm and is the same form factor as the RFSOM 
  
 +===== Size =====
  
-===== I/O Voltage =====+The size of the board (not including the SMA connectors, which project beyond the edge of the board) is 110mm x 69mm. The mounting holes align with the carrier card (EK-Z7-ZC706-G), and are shown below. 
 +{{ :resources:eval:user-guides:ad-fmcomms11-ebz:board_size.jpg |}}
  
-The AD-FMComms5 (AD9361) assumes a VDD_INTERFACE voltage between 1.71V and 2.625V (1.8 to 2.5 +/- 5%), so on your FPGA carrier board, you should ensure that V<sub>ADJ</sub> is between these levels. Setting things to 3.3V will damage the part. 
  
-===== Phase Synchronization =====+===== Layers =====
  
-Traces between baluns and SMAs are not phase matched on REV-A and REV-B which can cause phase misalignment with the libad9361-iio ad9361_fmcomms5_phase_sync solution. This is corrected on REV-C. Therefore, phase alignment performance can vary over frequency. The RF switches on REV-A/B are also not designed to work above 900 MHz. Higher frequency switches are available on REV-C.+The AD-FMCOMMS11-EBZ is a 12 layer board. 
 +{{ :resources:eval:user-guides:ad-fmcomms11-ebz:board_layer.jpg |}}
  
 + 
 +{{navigation AD-FMCOMMS11-EBZ|#none#|User Guide#prerequisites}}
  
resources/eval/user-guides/ad-fmcomms11-ebz/hardware.1550109225.txt.gz · Last modified: 14 Feb 2019 02:53 by erbe reyta

Page Tools