Next revision | Previous revision |
university:tools:uartjtag:hardware [09 Nov 2017 18:06] – created Neil Wilson | university:tools:uartjtag:hardware [29 Jan 2021 09:36] (current) – Fixed bad link for digikey Ioana Chelaru |
---|
====== ADALM-UARTJTAG hardware ====== | ====== ADALM-UARTJTAG hardware ====== |
| |
| Analog Devices provides a small adapter board [[../uartjtag|(ADALM-UARTJTAG)]] to be used for JTAG and UART, in order to make that easier for programming and debugging. You are encouraged to use this on your designs for the same reason we do - the standard JTAG connector is huge, and there are times where good old fashion console UART is valuable for doing debug. The 1.8V supply on the connector above is the I/O voltage, and can be used anywhere between 1.8V and 3.3V. |
| |
| In the box, you should have received the UARTJTAG board, ribbon cable, jumper, and [[https://www.samtec.com/products/ftsh|Samtec FTSH-105-01-L-D 10]] position dual row 0.05" through hole pin connector. |
| |
| {{ :university:tools:jtaguart:adalm-uartjtag.png?400 |}} |
| |
| The PCB includes a jumper, which forces the Zynq to HALT on JTAG. This is great for halting, and not allowing anything to run, but does does pull down a chip select for SPI flash, and will not allow the SPI flash to be found by the on chip bootloader, or by U-Boot. (If you are loading a U-Boot over JTAG). |
| |
| The pin connector is likely inserted into the ribbon cable: |
| |
| {{:university:tools:jtaguart:uartjtagcablepluspins2.png?direct&300|3 }} |
| {{ :university:tools:jtaguart:uartjtagcablepluspins.png?direct&200|4}} |
| |
| but can be removed, and either soldered to the PCB, or left in the ribbon cable, so you don't loose it. |
| |
| {{:university:tools:jtaguart:uartjtagcable.png?direct&300|2}} |
| |
| If you do want more, they can be obtained from [[https://www.samtec.com/products/ftsh-105-01-l-d|Samtec]], |
| [[digikey>SAM10499-ND|Digikey]] or [[https://www.arrow.com/en/products/ftsh-105-01-l-d/samtec|Arrow]]. |
| |
| ====== Downloads ====== |
| |
| |
<WRAP round download 65%> | <WRAP round download 65%> |
* {{:university:tools:jtaguart:adalm-jtaguart_fab.zip|Rev A Gerbers}} (This file is [[http://www.7-zip.org/7z.html|compressed]]) | * {{:university:tools:jtaguart:adalm-jtaguart_fab.zip|Rev A Gerbers}} (This file is [[http://www.7-zip.org/7z.html|compressed]]) |
* {{:university:tools:jtaguart:adalm-jtaguart.xlsx|Rev A Bill of materials}} | * {{:university:tools:jtaguart:adalm-jtaguart.xlsx|Rev A Bill of materials}} |
* {{:university:tools:jtaguart:adalm-jtaguart_brd.zip|Rev A Allegro Board File}} (This file is [[http://www.7-zip.org/7z.html|compressed]]). Get the [[http://www.cadence.com/products/pcb/Pages/downloads.aspx|Allegro FREE Physical Viewer]] to view. | * {{:university:tools:jtaguart:adalm-jtaguart_brd.zip|Rev A Allegro Board File}} (This file is [[http://www.7-zip.org/7z.html|compressed]]). Get the [[https://www.cadence.com/en_US/home/tools/pcb-design-and-analysis/allegro-downloads-start.html|Allegro FREE Physical Viewer]] to view. |
| </WRAP> |
| |
| <WRAP round download 65%> |
| * {{|Rev B Schematics}} |
| * {{|Rev B Gerbers}} (This file is [[http://www.7-zip.org/7z.html|compressed]]) |
| * {{|Rev B Bill of materials}} |
| * {{|Rev B Allegro Board File}} (This file is [[http://www.7-zip.org/7z.html|compressed]]). Get the [[https://www.cadence.com/en_US/home/tools/pcb-design-and-analysis/allegro-downloads-start.html|Allegro FREE Physical Viewer]] to view. |
</WRAP> | </WRAP> |
| |