Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий
This version is outdated by a newer approved version.DiffThis version (04 Apr 2022 18:39) is a draft.
Approvals: 0/1The Previously approved version (10 Mar 2022 14:43) is available.Diff

This is an old revision of the document!

Table of Contents

ADI maintains a set of tools to interface with ADI RF and microwave devices within MATLAB and Simulink. These are combined into single Toolbox which contains a set of Board Support Packages (BSP). The list of supported boards is provided below.

Quick Start with Toolbox

The current stable Toolbox can be downloaded from the RF Microwave Toolbox GitHub Release Page. Download the latest mltbx file then open that file within MATLAB. Opening the file will automatically install the Toolbox, adding the necessary components to your MATLAB path. The “Analog Devices, Inc. RF Microwave Toolbox” will appear in your Add-Ons Explore within MATLAB.

To interface and stream data with hardware will require installation of libiio and one of two Hardware Support Packages from MathWorks. The libiio library can be obtained on the Github page of the project.

Libiio Installers

Installation of either:

Skip the Zynq SDR or ADALM-PLUTO post-installation steps. They are not used. The FPGA carrier board SD card images are available on the AD-FMC-SDCARD for Zynq & Altera SoC Quick Start Guide page.

is required to use the streaming system objects or blocks. These support packages provide the necessary libIIO MATLAB bindings used by ADI's system objects.

Building the Toolbox Manually

The toolbox can only be built under Linux or with Cygwin on a Windows platform. Conveniently, the entire process is automated with a Makefile located in the CI/scripts folder of the repository. The following is required on the system before the build process can be run:

  • A supported MATLAB version installed in the default location (/usr/local/MATLAB)
  • A supported Vivado version installed in the default location (/opt/Xilinx)
  • Packages: git zip unzip tar make wget sed
You should only manually build the toolbox if you require a custom branch or no toolbox installer is available

First clone the repo and move into it: 

git clone https://github.com/analogdevicesinc/RFMicrowaveToolbox.git
cd RFMicrowaveToolbox

To build the toolbox run the following: 

make -C CI/scripts build

To create a installable tlbx file run: 

make -C CI/scripts gen_tlbx

Device Control and Data Streaming

Device interfaces which provide control and data streaming are implemented with MATLAB System Objects and Simulink Blocks. These System Objects can be access under the “adi” namespace in MATLAB and are followed by their part number or board name and finally Tx or Rx: 

adi.<Part or Board Name>.<Tx or Rx>

For example, to instantiate a ADAR3002 object to control the ADAR3002 beamformer it can be created as follows: 

bf = adi.ADAR3002;

All supported boards are derived from low level objects based on their parts. For example, the LongsPeak Evaluation board contains an AD9680 and AD9144. Therefore, it simply uses ADAR300x and ADMV4420 objects under the hood. However, to interact with the more familiar LongsPeak interface, it can be instantiated like above as: 

bf = adi.LongsPeak;

For example usage of certain objects, it can be useful to inspect their related test code which exercises initiations in different configurations. The available code is available in the GitHub repo folder here, where object tests have the naming convention <Object>Tests.m.

To get a list of currently available objects with the BSP installed simply run: 

help adi

To get more information on a given object run: 

help adi.<Part of Board Name>.<Tx or Rx>

or 

doc adi.<Part of Board Name>.<Tx or Rx>

Common Attributes

There are some common attributes that need to be set for system objects and parts.

  • uri Context address of IIO device.
    • IP with usage rx.uri = 'ip:192.168.2.1'

Extending Interfaces

If a driver attribute or setting is not available in the standard objects it can be easily extended to cover more IIO attributes. See this guide.

Examples

Examples for streaming data and targeting FPGAs are listed within the Toolbox documentation itself. To view run the following with MATLAB: 

doc adi

Help & Support

resources/tools-software/rf-microwave-toolbox.1649090385.txt.gz · Last modified: 04 Apr 2022 18:39 by Srikanth Pagadarai

Page Tools