| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| resources:eval:user-guides:inertial-mems:imu:adis16acl2-pcb [10 Dec 2016 00:38] – [ORDERING] Mark Looney | resources:eval:user-guides:inertial-mems:imu:adis16acl2-pcb [13 Dec 2016 16:04] (current) – [OVERVIEW] Mark Looney |
|---|
| ====== ADIS16ACL2/PCB WIKI GUIDE ====== | ====== ADIS16ACL2/PCB WIKI GUIDE ====== |
| ===== OVERVIEW ===== | ===== OVERVIEW ===== |
| The ADIS16223 and ADIS16227 products use a 14-pin flexible interface. The mating connector for their interface supports surface-mount solder attachment but does not support direct attachment with ribbon cables. For those who are would like to connect the ADIS16223 and ADIS16227 to an existing processor board, using a ribbon cable, the ADIS16ACL2/PCBZ provides a simple connector translation for this purpose. | The ADIS16ACL2/PCBZ is the breakout board for the ADIS16223 and ADIS16227 vibration sensing solutions. This breakout board function helps connect these two products to the EVAL-ADIS2 evaluation system. It also helps connect these products to existing embedded processor platforms. |
| |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_000.png?600|}} | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_000.png?600|}} |
| |
| ===== ADIS16223/ADIS16227 Connection ===== | ===== ADIS16223/ADIS16227 Connection ===== |
| ADD INSTRUCTION HERE | Press the ADIS16223/7 connector onto J2 (14-pin socket). |
| |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl1-pcb_pic_01.png?600|}} | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_003.png?450|}} |
| |
| ===== EVAL-ADIS2 Connection ===== | ===== EVAL-ADIS2 Connection ===== |
| The EVAL-ADIS2 provides PC-based evaluation support for the ADIS16210 and ADIS16228. J1 on the EVAL-ADIS2Z and the ADIS16ACL1/PCBZ use the same pin assignments, so connecting them requires a 16-pin ribbon cable. | The EVAL-ADIS2 provides PC-based evaluation support for the ADIS16223 and ADIS16227. J1 on the EVAL-ADIS2Z and the ADIS16ACL2/PCBZ use the same pin assignments, so connecting them requires a 16-pin ribbon cable. |
| |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl1-pcb_pic_02.png?600|}} | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_002.png?600|}} |
| |
| ===== Electrical Schematic ===== | ===== Electrical Schematic ===== |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl1-pcb_pic_03.png?800|}} | |
| |
| ===== Outer Dimensions ===== | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_004.png?800|}} |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl1-pcb_pic_0003.png?400|}} | |
| |
| | ===== Outer Dimensions ===== |
| | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_005.png?400|}} |
| ===== Mounting Holes ===== | ===== Mounting Holes ===== |
| {{:resources:eval:user-guides:inertial-mems:imu:adis16acl1-pcb_pic_0004.png?400|}} | {{:resources:eval:user-guides:inertial-mems:imu:adis16acl2_pcb_web_006.png?400|}} |
| |
