Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:circuits-from-the-lab:cn0187 [29 Sep 2017 07:57] – [Advanced] erbe reytaresources:eval:user-guides:circuits-from-the-lab:cn0187 [30 Jul 2021 07:14] (current) – Victor Calinao, Jr
Line 9: Line 9:
  
 ===== General Setup ===== ===== General Setup =====
-  * [[http://www.analog.com/EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] Evaluation Board +  * [[adi>EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] Evaluation Board 
-  * [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Evaluation Board+  * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Evaluation Board
   * [[ftp://ftp.analog.com/pub/cftl/CN0187|CN0187 Evaluation Software]]   * [[ftp://ftp.analog.com/pub/cftl/CN0187|CN0187 Evaluation Software]]
     * (supplied with provided CD in kit)     * (supplied with provided CD in kit)
Line 41: Line 41:
 ===== Connecting the Hardware ===== ===== Connecting the Hardware =====
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0187:cn0187_block_diagram_v1.png |}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0187:cn0187_block_diagram_v1.png |}}
-  - Connect the 120-pin connector on the [[http://www.analog.com/EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] circuit board to the connector marked “CON A” on the EVAL-SDP-CB1Z evaluation (SDP) board. Nylon hardware should be used to firmly secure the two boards, using the holes provided at the ends of the 120-pin connectors as depicted in the image below. +  - Connect the 120-pin connector on the [[adi>EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] circuit board to the connector marked “CON A” on the EVAL-SDP-CB1Z evaluation (SDP) board. Nylon hardware should be used to firmly secure the two boards, using the holes provided at the ends of the 120-pin connectors as depicted in the image below. 
-  - Using an appropriate RF cable, connect the RF signal source to the [[http://www.analog.com/EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] board via the SMA RF input connector.+  - Using an appropriate RF cable, connect the RF signal source to the [[adi>EVAL-CN0187-SDPZ|EVAL-CN0187-SDPZ]] board via the SMA RF input connector.
   - With power to the supply off, connect a +6 V power supply to the pins marked “+6 V” and “GND” on the board. If available, a +6 V "wall wart" can be connected to the barrel jack connector on the board and used in place of the +6 V power supply.    - With power to the supply off, connect a +6 V power supply to the pins marked “+6 V” and “GND” on the board. If available, a +6 V "wall wart" can be connected to the barrel jack connector on the board and used in place of the +6 V power supply. 
-  - Connect the USB cable, supplied along with the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation board, from the SDP board to the USB port on the PC.+  - Connect the USB cable, supplied along with the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation board, from the SDP board to the USB port on the PC.
  
 ---- ----
Line 159: Line 159:
   * {{:resources:eval:user-guides:circuits-from-the-lab:cn0187:eval-cn0187-sdpz-assemblydrawing-revb.pdf|Assembly Drawing}}(PDF)   * {{:resources:eval:user-guides:circuits-from-the-lab:cn0187:eval-cn0187-sdpz-assemblydrawing-revb.pdf|Assembly Drawing}}(PDF)
 </WRAP> </WRAP>
 +
 +=====Registration===== 
 +<WRAP round tip 80% >
 +Receive software update notifications, documentation updates, view the latest videos, and more when you register your hardware.  [[reg>EVAL-CN0187-SDPZ?&v=Rev B|Register]] to receive all these great benefits and more!</WRAP>
  
 // End of Document // // End of Document //
resources/eval/user-guides/circuits-from-the-lab/cn0187.1506664647.txt.gz · Last modified: 29 Sep 2017 07:57 by erbe reyta

Page Tools