Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:controller_board [05 Feb 2014 16:18] – [ADC FPGA Interface] Andrei Cozmaresources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:controller_board [05 Feb 2014 17:41] – [Jumper settings] Mihai Bancisor
Line 26: Line 26:
  
 ^  Measurement  ^^ ^  Measurement  ^^
-| **[[adi>AD7401A|AD7401A]]** | 5 kV rms, isolated 2nd order Sigma-Delta modulator |+| **[[AD7401A]]** | 5 kV rms, isolated 2nd order Sigma-Delta modulator |
 | **[[adi>ADA4084-2|ADA4084-2]]** | 30 V, Low noise, rail-to-rail I/O, low power operational amplifier | | **[[adi>ADA4084-2|ADA4084-2]]** | 30 V, Low noise, rail-to-rail I/O, low power operational amplifier |
 | **[[adi>AD8646|AD8646]]** | 24 MHz rail-to-rail dual op amp | | **[[adi>AD8646|AD8646]]** | 24 MHz rail-to-rail dual op amp |
Line 47: Line 47:
 ^  ^ ^  ^
  
 +===== Jumper settings =====
 +{{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:controller_jumpers.jpg?600|AD-FMC-MOTCON1-EBZ Jumpers}}
  
 +|< 100% 25%  40% 35% >|
 +^  Sensor Selection  ^^^
 +| **Back EMF** | P9 - position 0 | P20 - position 0 |
 +| **Single ended Hall** | P9 - position 1 | P20 - position 0 |
 +| **Differential Hall** | P9 - position 0 | P20 - position 1 |
 +| **Reserved** | P9 - position 1 | P20 - position 1 |
 +^  Resolver Comfiguration Mode  ^^^
 +| **Normal Mode - Position input** | P3 - Not inserted | P5 - Not inserted |
 +| **Normal Mode - Velocity input** | P3 - Not inserted | P5 - Inserted |
 +| **Reserved** | P3 - Inserted | P5 - Not inserted |
 +| **Configuration Mode** | P3 - Inserted | P5 - Inserted |
 +^  Resolver Resolution Settings  ^^^
 +| **10 Bits** | P4 - Not inserted | P6 - Not inserted |
 +| **12 Bits** | P4 - Not inserted | P6 - Inserted |
 +| **14 Bits** | P4 - Inserted | P6 - Not inserted |
 +| **16 Bits** | P4 - Inserted | P6 - Inserted |
 +^  PHYs Configuration  ^^^
 +| **2.5V VDDO, different PHY addresses** | P11 & P12  - Position 0 | P9 - Inserted |
 +
 +
 +|< 100% 100% >|
 +^  ^
  
 ===== Power Map ===== ===== Power Map =====
resources/eval/user-guides/ad-fmcmotcon1-ebz/hardware/controller_board.txt · Last modified: 10 Feb 2021 04:42 by Robin Getz

Page Tools