Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:developer-kits:x-band-dev-kit:hardware-connections [22 Mar 2022 19:01] – XUD1A to Stingray Connection update Sam Ringwoodresources:eval:developer-kits:x-band-dev-kit:hardware-connections [17 May 2022 17:27] (current) – Sam Ringwood
Line 17: Line 17:
 \\  \\ 
 ==== RF Connectors ==== ==== RF Connectors ====
-  - The Stingray board uses SMPM connectors on both sides of the board, so depending on how the board is used, adapters to mate with test equipment cabling may be required. Note that the Stingray board includes 2x 12" SMPM-SMA cables \\ One example adapter cable: [[https://www.centricrf.com/cable-assemblies/mini-smp-cable-assemblies/27-ghz-047-mini-smp-to-sma|SMPM to SMA Adapter Cable]] +  - The Stingray board uses SMPM connectors on both sides of the board, so depending on how the board is used, adapters to mate with test equipment cabling may be required. Note that the Stingray board includes 1x 12" SMPM-SMA cable. \\ One example adapter cable: [[https://www.centricrf.com/cable-assemblies/mini-smp-cable-assemblies/27-ghz-047-mini-smp-to-sma|SMPM to SMA Adapter Cable]] 
-  - The XUD1a board uses SMA connectors on the RF side of the board and SMPM connectors on the IF side of the board.+  - The XUD1a board uses SMA connectors on the RF side of the board and SMPM connectors on the IF side of the board. Note that the XUD1A board includes 1x 12" SMPM-SMA cable.
   - The MxFE board uses SMA connectors for both the ADCs and DACs.   - The MxFE board uses SMA connectors for both the ADCs and DACs.
  
Line 27: Line 27:
   - J55 from the ZCU102 should connect to P3 on the Stingray board using a ribbon cable and any required adapters. Note that pin 1 should connect to pin 1. This will require two PMOD cables to vertically flip the pinout from the ZCU102 to match that of the Stingray board. \\ \\    - J55 from the ZCU102 should connect to P3 on the Stingray board using a ribbon cable and any required adapters. Note that pin 1 should connect to pin 1. This will require two PMOD cables to vertically flip the pinout from the ZCU102 to match that of the Stingray board. \\ \\ 
   - J87 from the ZCU102 should connect to P4 on the Stingray board using a ribbon cable and any required adapters. Note that pin 1 should connect to pin 1. This will require two PMOD cables to vertically flip the pinout from the ZCU102 to match that of the Stingray board.   - J87 from the ZCU102 should connect to P4 on the Stingray board using a ribbon cable and any required adapters. Note that pin 1 should connect to pin 1. This will require two PMOD cables to vertically flip the pinout from the ZCU102 to match that of the Stingray board.
 +
 +
 +{{ :resources:eval:developer-kits:x-band-dev-kit:stingray_zcu102_pmod.png?600 |}}
  
 \\ \\
 ===== XUD1a: ADXUD1AEBZ ===== ===== XUD1a: ADXUD1AEBZ =====
-Connect the XUD1a evaluation board to the ZCU102's HPC1 port as shown below. The [[digikey>HDR-169468-01|FMC extension]] is used both to move the interposer board and XUD1a away from the MxFE evaluation board as well as to allow access to the HPC1 connector which is otherwise blocked by the MxFE evaluation board. +Connect the XUD1a evaluation board to the ZCU102's HPC1 port. The [[digikey>HDR-169468-01|FMC extension]] is used both to move the interposer board and XUD1a away from the MxFE evaluation board as well as to allow access to the HPC1 connector which is otherwise blocked by the MxFE evaluation board. 
-{{ /resources/eval/developer-kits/x-band-dev-kit/xud_connection.jpg?1000 |XUD1a Connection}}+ 
 +{{ :resources:eval:developer-kits:x-band-dev-kit:xud1a_fmc_v2.png?600 |}}
  
 \\ \\
Line 68: Line 72:
 ^  4  |  J1A (SMA)  |  4 (SMA)  | ^  4  |  J1A (SMA)  |  4 (SMA)  |
  
 +===== Support =====
 +For additional questions or support, please visit the Engineering Zone forum at [[ez>ADEF]]. 
 +
 +[[resources/eval/developer-kits/x-band-dev-kit|X Band Development Platform]]
resources/eval/developer-kits/x-band-dev-kit/hardware-connections.1647972085.txt.gz · Last modified: 22 Mar 2022 19:01 by Sam Ringwood

Page Tools