Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revisionBoth sides next revision
university:tools:m2k:scopy:test-cases:logic-analyzer_temp [16 Apr 2021 03:58] – Updated for new features Trecia Agoylouniversity:tools:m2k:scopy:test-cases:logic-analyzer_temp [16 Apr 2021 04:01] – Trecia Agoylo
Line 49: Line 49:
 | ::: | 4. Set logic analyzer’s settings to sample rate: 100Msps, position: 0s. Set pattern generator DIO0’s parameters to: Pattern: clock, Frequency: 2.5MHz, Phase: 0 degrees and Duty Cycle: 50%.  | {{ :university:tools:m2k:scopy:test-cases:individual_operation-step4c.png?200 |}}| Refer to the step resource picture | | ::: | 4. Set logic analyzer’s settings to sample rate: 100Msps, position: 0s. Set pattern generator DIO0’s parameters to: Pattern: clock, Frequency: 2.5MHz, Phase: 0 degrees and Duty Cycle: 50%.  | {{ :university:tools:m2k:scopy:test-cases:individual_operation-step4c.png?200 |}}| Refer to the step resource picture |
 | ::: | 5. Move the cursors to the consecutive rising edges or consecutive falling edges| {{ :university:tools:m2k:scopy:test-cases:individual_operation-step5c.png?200 |}}|The data measured by the cursor should be close to ∆t: 400ns and 1/∆t: 2.5MHz| | ::: | 5. Move the cursors to the consecutive rising edges or consecutive falling edges| {{ :university:tools:m2k:scopy:test-cases:individual_operation-step5c.png?200 |}}|The data measured by the cursor should be close to ∆t: 400ns and 1/∆t: 2.5MHz|
-| ::: | 6. Enable Lock cursor feature and measure the next edges| |}}|The data measured by the cursor should be close to ∆t: 400ns and 1/∆t: 2.5MHz|+| ::: | 6. Enable Lock cursor feature and measure the next edges| |The data measured by the cursor should be close to ∆t: 400ns and 1/∆t: 2.5MHz|
 | ::: | 7. Set logic analyzer’s settings to sample rate: 20ksps. Set pattern generator DIO0’s parameters to: Pattern: clock, Frequency: 100Hz, Phase: 0 degrees and Duty Cycle: 70%.  | {{ :university:tools:m2k:scopy:test-cases:individual_operation-step7.0c.png?200 |}}| Refer to the step resource. | | ::: | 7. Set logic analyzer’s settings to sample rate: 20ksps. Set pattern generator DIO0’s parameters to: Pattern: clock, Frequency: 100Hz, Phase: 0 degrees and Duty Cycle: 70%.  | {{ :university:tools:m2k:scopy:test-cases:individual_operation-step7.0c.png?200 |}}| Refer to the step resource. |
 | ::: | 8. Move the cursors to the rising and falling edge of the upper limit| {{ :university:tools:m2k:scopy:test-cases:individual_operation-step8c.png?200 |}}|The data measured by the cursor should be close to ∆t: 7ms| | ::: | 8. Move the cursors to the rising and falling edge of the upper limit| {{ :university:tools:m2k:scopy:test-cases:individual_operation-step8c.png?200 |}}|The data measured by the cursor should be close to ∆t: 7ms|
Line 61: Line 61:
 ^ Description                           ^ Test Steps     ^ Steps Resources ^ Expected Results ^   ^ Description                           ^ Test Steps     ^ Steps Resources ^ Expected Results ^  
  
-| Parallel Mode | 1. In logic analyzer, add a parallel decoder. Set Clock line to DIO8 and set Data lines 0-7 to DIO0 to DIO7. In pattern generator, group DIO0 to DIO7 set as number pattern. Enbale DIO8 and set to Clock with 500Hz frequency. | {{ :university:tools:m2k:scopy:test-cases:group_operation-step1.0a.png?200 |}}{{ :university:tools:m2k:scopy:test-cases:group_operation-step1.1a.png?200 |}}| The interface should look like in the "Step Resources" picture (left side).|+| Parallel Mode | 1. In logic analyzer, add a parallel decoder. Set Clock line to DIO8 and set Data lines 0-7 to DIO0 to DIO7. In pattern generator, group DIO0 to DIO7 set as number pattern. Enable DIO8 and set to Clock with 500Hz frequency. | {{ :university:tools:m2k:scopy:test-cases:group_operation-step1.0a.png?200 |}}{{ :university:tools:m2k:scopy:test-cases:group_operation-step1.1a.png?200 |}}| The interface should look like in the "Step Resources" picture (left side).|
 | ::: | 2. Run the Pattern Generator and Logic analyzer instrument. Set in the pattern generator’s instrument the desired decimal value.| {{ :university:tools:m2k:scopy:test-cases:group_operation-step2a.png?200 |}}| On the logic analyzer plot, the reading is in hex format. For reference, 50 decimal = 32 hex, 100 decimal =  64 hex and 250 decimal = FA | | ::: | 2. Run the Pattern Generator and Logic analyzer instrument. Set in the pattern generator’s instrument the desired decimal value.| {{ :university:tools:m2k:scopy:test-cases:group_operation-step2a.png?200 |}}| On the logic analyzer plot, the reading is in hex format. For reference, 50 decimal = 32 hex, 100 decimal =  64 hex and 250 decimal = FA |
 | ::: | 3. In logic analyzer, add another parallel decoder. Set Clock line to DIO8 and set Data lines 0-6 to DIO9 to DIO15.In pattern generator, group DIO9 to DIO15 set as number pattern| {{ :university:tools:m2k:scopy:test-cases:group_operation-step3.0a.png?200 |}}{{ :university:tools:m2k:scopy:test-cases:group_operation-step3.1a.png?200 |}}| The interface should look like in the "Step Resources" picture (left side).| | ::: | 3. In logic analyzer, add another parallel decoder. Set Clock line to DIO8 and set Data lines 0-6 to DIO9 to DIO15.In pattern generator, group DIO9 to DIO15 set as number pattern| {{ :university:tools:m2k:scopy:test-cases:group_operation-step3.0a.png?200 |}}{{ :university:tools:m2k:scopy:test-cases:group_operation-step3.1a.png?200 |}}| The interface should look like in the "Step Resources" picture (left side).|
university/tools/m2k/scopy/test-cases/logic-analyzer_temp.txt · Last modified: 30 Sep 2022 09:40 by Andrei Popa

Page Tools