Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
university:tools:m2k:accessories:power [27 Aug 2021 14:01] – Replaced pictures Pop Andreeauniversity:tools:m2k:accessories:power [18 Mar 2022 15:38] – Gains Pop Andreea
Line 3: Line 3:
 The AD-M2KPWR-EBZ is an ADALM2000 add-on board which increases the output current capability up to 700mA. This board can be also used as a standalone benchtop power supply with positive and negative outputs. The AD-M2KPWR-EBZ is an ADALM2000 add-on board which increases the output current capability up to 700mA. This board can be also used as a standalone benchtop power supply with positive and negative outputs.
  
 +{{:university:tools:m2k:accessories:ad-m2kbnc-ebz-top-web.png?400|}}
 +{{:university:tools:m2k:accessories:ad-m2kpwr-ebz-bottom-web.png?400|}}
  
-{{:university:tools:m2k:accessories:ad-m2kpwr-ebztop.jpg?500|}} 
-{{:university:tools:m2k:accessories:ad-m2kpwr-ebzbottom.jpg?500|}} 
  
 Figure 1. AD-M2KPWR-EBZ Top view and bottom view Figure 1. AD-M2KPWR-EBZ Top view and bottom view
Line 42: Line 42:
   * Standoffs and screws   * Standoffs and screws
  
 +{{:university:tools:m2k:accessories:ad-m2kbnc-ebz-angle-web.png?500|}}
  
-{{:university:tools:m2k:accessories:ad-m2kpwr-ebzangle.jpg?400|}} 
  
  
Line 50: Line 50:
 AD-M2KPWR-EBZ  must be supplied either from a 5.1V 3A USB Type C power adapter or from a lab supply using the screw terminal connector. Make sure that the jumper on the P2 connector is on the position corresponding to the chosen supply: AD-M2KPWR-EBZ  must be supplied either from a 5.1V 3A USB Type C power adapter or from a lab supply using the screw terminal connector. Make sure that the jumper on the P2 connector is on the position corresponding to the chosen supply:
  
-<WRAP centeralign>{{:university:tools:m2k:accessories:vusbconn.png?600|}}</WRAP>+<WRAP centeralign>{{:university:tools:m2k:accessories:m2kpwr_supply_jumper.png?600|}}</WRAP>
 <WRAP centeralign> Figure 3. AD-M2KPWR-EBZ supply select jumper</WRAP> <WRAP centeralign> Figure 3. AD-M2KPWR-EBZ supply select jumper</WRAP>
 ^ P2 ^ Selected supply method^  ^ P2 ^ Selected supply method^ 
Line 58: Line 58:
  
  
-<WRAP centeralign>{{:university:tools:m2k:accessories:20210615_1452544.jpg?600|}}</WRAP>+
 <WRAP centeralign> Figure 4.AD-M2KPWR-EBZ connected to ADALM2000 and USB Type C supply</WRAP> <WRAP centeralign> Figure 4.AD-M2KPWR-EBZ connected to ADALM2000 and USB Type C supply</WRAP>
  
Line 66: Line 66:
  
  
-<WRAP centeralign>  {{:university:tools:m2k:accessories:jumpers_mode_selection.png?600|}}</WRAP>+<WRAP centeralign> {{:university:tools:m2k:accessories:m2kpwr_pot_control.png?600|}} </WRAP>
 <WRAP centeralign> Figure 5. AD-M2KPWR-EBZ POT/M2K mode setup jumpers</WRAP> <WRAP centeralign> Figure 5. AD-M2KPWR-EBZ POT/M2K mode setup jumpers</WRAP>
  
Line 82: Line 82:
  
  
 +====Gain====
 +The board can be adjusted such as the output voltage is double or triple than the value set from the M2K. This feature is only available in M2K mode, and it is activated by soldering or desoldering the solderjumpers on the bottom of the board according to the table. 
 +You can find the table with the soldering instructions on the bottom of the board.
  
  
university/tools/m2k/accessories/power.txt · Last modified: 05 May 2022 12:44 by Pop Andreea

Page Tools