Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
university:courses:electronics:electronics-lab-7 [05 Mar 2019 12:23] – [Procedure:] Antoniu Miclausuniversity:courses:electronics:electronics-lab-7 [23 Aug 2019 12:52] – Antoniu Miclaus
Line 1: Line 1:
-====== Activity 7. Zero gain amplifier (BJT) ======+====== Activity: Zero gain amplifier (BJT) ======
  
 ===== Objective: ===== ===== Objective: =====
Line 25: Line 25:
 ===== Hardware Setup: ===== ===== Hardware Setup: =====
  
-The waveform generator 1 should be configured for a 1 KHz triangle wave with 3 volt amplitude and 1.5V offset. Connect scope Channel 1 to display output W1 of the AWG generator. The Single ended input of scope channel 2 (2+) is used to measure alternately the base and collector voltage of Q<sub>1</sub>.+The waveform generator 1 should be configured for a 1 KHz triangle wave with 3 volt amplitude peak-to-peak and 1.5V offset. Connect scope Channel 1 to display output W1 of the AWG generator. The Single ended input of scope channel 2 (2+) is used to measure alternately the base and collector voltage of Q<sub>1</sub>.
  
 {{:university:courses:electronics:zero_gain-bb.png|}} {{:university:courses:electronics:zero_gain-bb.png|}}
Line 85: Line 85:
  
  
-The waveform generator should be configured for a 1 KHz triangle wave with 3 volt amplitude and 1.5V offset. Both scope channels can be set to 200mV per division.+The waveform generator should be configured for a 1 KHz triangle wave with 3 volt amplitude peak-to-peak and 1.5V offset. Both scope channels can be set to 200mV per division.
  
 ===== Procedure: ===== ===== Procedure: =====
Line 124: Line 124:
 <WRAP centeralign> Figure 12 V<sub>BE</sub> Multiplier Breadboard circuit </WRAP> <WRAP centeralign> Figure 12 V<sub>BE</sub> Multiplier Breadboard circuit </WRAP>
  
-The waveform generator should be configured for a 1KHz triangle wave with 3 volt amplitude and 1.5V offset. Both scope channels can be set to 200mV per division.+The waveform generator should be configured for a 1KHz triangle wave with 3 volt amplitude peak-to-peak and 1.5V offset. Both scope channels can be set to 200mV per division.
  
 ===== Procedure: ===== ===== Procedure: =====
Line 173: Line 173:
 <WRAP centeralign> Figure 18 Version 3 of V<sub>BE</sub> multiplier Breadboard Circuit</WRAP> <WRAP centeralign> Figure 18 Version 3 of V<sub>BE</sub> multiplier Breadboard Circuit</WRAP>
  
-The waveform generator should be configured for a 1KHz triangle wave with 3 volt amplitude and 1.5V offset. Both scope channels can be set to 200mV per division.+The waveform generator should be configured for a 1KHz triangle wave with 3 volt amplitude peak-to-peak and 1.5V offset. Both scope channels can be set to 200mV per division.
  
 ===== Procedure: ===== ===== Procedure: =====
university/courses/electronics/electronics-lab-7.txt · Last modified: 25 Jun 2020 22:07 by 127.0.0.1

Page Tools