Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
university:courses:electronics:comms-lab-clapp-osc [27 Mar 2017 17:11] – [Materials:] Doug Merceruniversity:courses:electronics:comms-lab-clapp-osc [05 Mar 2019 12:57] – [Questions:] Antoniu Miclaus
Line 52: Line 52:
 =====Hardware Setup:===== =====Hardware Setup:=====
  
-The green squares indicate where to connect the Discovery module AWG, scope channels and power supplies. Be sure to only turn on the power supplies after you double check your wiring.+<WRAP centeralign>{{ :university:courses:electronics:clapp_osc-bb.png |}}</WRAP> 
 + 
 +<WRAP centeralign> Figure 3 Clapp Oscillator Breadboard circuit </WRAP> 
 + 
 +The green squares indicate where to connect the ADALM2000 module AWG, scope channels and power supplies. Be sure to only turn on the power supplies after you double check your wiring.
  
 =====Procedure:===== =====Procedure:=====
  
 Having finished construction the Clapp oscillator check that the circuit is oscillating correctly by turning on both the + and - 5 V power supplies and connecting one of the oscilloscope channels to the output terminal. It may be found that the value of R<sub>3</sub> is fairly critical, producing either a large distorted waveform or an intermittent low or no output. To find the best value for R<sub>3</sub>, it could be replaced by a 1 KΩ potentiometer for experimentation to find the value that gives the best wave shape and reliable amplitude. Having finished construction the Clapp oscillator check that the circuit is oscillating correctly by turning on both the + and - 5 V power supplies and connecting one of the oscilloscope channels to the output terminal. It may be found that the value of R<sub>3</sub> is fairly critical, producing either a large distorted waveform or an intermittent low or no output. To find the best value for R<sub>3</sub>, it could be replaced by a 1 KΩ potentiometer for experimentation to find the value that gives the best wave shape and reliable amplitude.
 +
 +A plot example using R<sub>1</sub>=10KΩ, R<sub>2</sub>=1KΩ, R<sub>3</sub>=100Ω, L<sub>1</sub>=100uH, L<sub>2</sub>=10uH, C<sub>1</sub>=1nF, C<sub>2</sub>=4.7nF, C<sub>3</sub>=10nF is presented in Figure 4.
 +
 +<WRAP centeralign>{{ :university:courses:electronics:clapp_osc-wav.png |}}</WRAP>
 +
 +<WRAP centeralign> Figure 4 Clapp Oscillator plot </WRAP>
  
 =====Questions:===== =====Questions:=====
Line 71: Line 81:
 |50 uH|  |  | |50 uH|  |  |
 |100 uH|  |  | |100 uH|  |  |
 +
 +<WRAP round download>
 +**Lab Resources:**
 +  * Fritzing files: [[ https://minhaskamal.github.io/DownGit/#/home?url=https://github.com/analogdevicesinc/education_tools/tree/master/m2k/fritzing/clapp_osc_bb | clapp_osc_bb]]
 +</WRAP>
  
 **For Further Reading:** **For Further Reading:**
university/courses/electronics/comms-lab-clapp-osc.txt · Last modified: 25 Jun 2020 22:07 by 127.0.0.1

Page Tools