This version (12 May 2023 07:15) was approved by Vasileios Bimpikas.
Testing for Release 3.0.0
| Testing Component | SC598-SOM-EZKIT | SC594-SOM-EZKIT | SC589-EZKIT | SC589-MINI | SC584-EZKIT | SC573-EZKIT |
|---|---|---|---|---|---|---|
| SRU DAI routing configuration | ✅ | ✅ | ✅ | ✅ | ||
| SPORT sending I2S data to CODECs | ✅ | ✅ | ✅ | ✅ | ||
| ADAU1761 Audio In Driver | N/A | N/A | N/A | ✅ | N/A | N/A |
| ADAU1962 Audio Out Driver | ✅ | ✅ | ✅ | N/A | ✅ | ✅ |
| ADAU1979 Audio In Driver | ✅ | ✅ | ✅ | N/A | ✅ | ✅ |
| ICAP | ✅ | N/A | N/A | N/A | N/A | N/A |
| SHARC ALSA | ✅ | N/A | N/A | N/A | N/A | N/A |
| remoteproc | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| virtio rpmsg | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| Common Clock Framework | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| CRC Check Using Crypto Framework | ✅ | N/A | N/A | N/A | N/A | N/A |
| DMA Peripheral Implicitly tested as it's used by SPI, OSPI, and UART drivers | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| MDMA Implicitly tested as it's used only by remoteproc to load data to SHARC shared memory | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| EMAC0 (eth0) | ✅ (950 Mbit/s) | ✅ (450 Mbit/s) | ✅ (190 Mbit/s) | ✅ (180 Mbit/s) | ✅ (190 Mbit/s) | ✅ (180 Mbit/s) |
| EMAC0 (AVB) | ❔ | ❔ | ❔ | ❔ | ❔ | ❔ |
| EMAC11 | ❗ | ❗ | ❔ | ❔ | ❔ | ❔ |
| GPIO Control | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| GPTimers | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| I2C | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| SRAM/L2 alloc | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| Pin Control Driver | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| RCU driver/system reset | ✅ | ✅ | ✅ | ❌2 | ✅ | ✅ |
| SPI | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| QSPI Boot | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| eMMC dev/mmcblk0 | ✅ | ✅ | N/A | N/A | N/A | N/A |
| eMMC Boot3 | ❗ | ❔ | N/A | N/A | N/A | N/A |
| SD dev/mmcblk0 | ✅ | N/A | ✅ | ✅ | N/A | ❔ |
| SD Boot | ✅ | N/A | ✅ | ✅ | N/A | ✅ |
| OSPI4 | ❗ | ❗ | N/A | N/A | N/A | N/A |
| uart0 | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
| USB: Host | ✅ | ✅ | ✅ | ✅ | ✅ | ❔ |
| USB: Device | ❔ | ❔ | ❔ | ❔ | ❔ | ❔ |
| Watchdog | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
✅ PASS
❗ PASS with warning(s), see note
N/A Not Applicable
❌ Not Tested
1Currently, the driver can enumerate the IP and identify what is present, but the PHY is not configured/reset yet and so ethernet communications do not work.
2There is a known issue on the SC589-MINI's watchdog which prevents the RCU driver/system from resetting properly
3Currently, booting with the kernel and RFS on SD/eMMC is the only supported configuration, primarily due to hardware limitations on the SOM-CRR-EZKIT (so U-Boot must still be stored on the SPI flash). See more in the relevant example
4OSPI is not currently working for MX66 chip under 5.15 kernel. OSPI (1S-8S-8S mode) does work for SC594 & IS25LX256
resources/tools-software/linuxdsp/docs/testing/release3.0.0.txt · Last modified: 11 May 2023 17:33 by Vasileios Bimpikas