Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий
This version is outdated by a newer approved version.DiffThis version (08 Dec 2020 08:35) was approved by Sunny Feng.

This is an old revision of the document!

Table of Contents

Ethernet Driver in U-Boot on SC5xx-EZKIT

Overview

Ethernet driver provides driver for the MAC controller present in ADI processors. The ethernet driver package also has code to interface with the PHYs on the ADI released boards.

There are 2 network interfaces on ADSP-SC5xx : EMAC0 and EMAC1

  • EMAC0 is configurable as 10/100 Mbps, interfacing via RMII, or 10/100/1000 Mbps, interfacing via RGMII. On the SC5xx-EZ-Board the RGMII interface is used, providing 10/100/1000 Mbps (gigabit) capability
  • EMAC1 is a fixed 10/100 Mbps EMAC, interfacing via RMII.

Hardware Setup

  • ADSP-SC589 Ezkit v1.1 and above, or,
  • ADSP-SC584 Ezkit v1.0 and above, or,
  • ADSP-SC573 Ezkit v1.2 (BOM 1.8) and above

Build U-Boot with emac0 or emac1

U-Boot only supports one network port.  You have to select one emac port in include/configs/sc589-ezkit.h at build time.(For SC584/SC573 EZ-Board , we should do it in file sc584-ezkit.h or sc573-ezkit.h) 

#define CONFIG_DW_PORTS         1  // enable EMAC0
or
#define CONFIG_DW_PORTS         2  // enable EMAC1

Using EMAC Driver

U-boot provides a set of basic net commands:

  • dhcp    - invoke a DHCP client request to obtain IP/boot params
  • ping    - send a ICMP ECHO_REQUEST to the network host
  • tftpboot - boot an image via network using the TFTP protocol

For example: 

CPU:   ADSP ADSP-SC589-0.0 (Detected Rev: 1.1) (spi flash boot)
VCO: 450 MHz, Cclk0: 450 MHz, Sclk0: 112.500 MHz, Sclk1: 112.500 MHz, DCLK: 225 MHz
OCLK: 150 MHz
I2C:   ready
DRAM:  112 MiB
MMC:   SC5XX SDH: 0
SF: Detected W25Q128BV with page size 256 Bytes, erase size 4 KiB, total 16 MiB
In:    serial
Out:   serial
Err:   serial
other init
Net:   dwmac.3100c000
Hit any key to stop autoboot:  0 
sc #  
sc # dhcp
Speed: 100, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 10.99.24.200 (260 ms)
sc # ping 10.99.24.94
Speed: 100, full duplex
Using dwmac.3100c000 device
host 10.99.24.94 is alive
sc # tftp ${loadaddr} ${ramfile}
Speed: 100, full duplex
Using dwmac.3100c000 device
TFTP from server 10.99.24.94; our IP address is 10.99.24.200
Filename 'uImage'.
Load address: 0x89000000
Loading: #################################################################
	 #################################################################
......
 #####################################
	 2 MiB/s
done
Bytes transferred = 10502080 (a03fc0 hex)

 


Back To: Das U-boot

resources/tools-software/linuxdsp/docs/das-u-boot/ethernet_driver_in_uboot.1607412922.txt.gz · Last modified: 08 Dec 2020 08:35 by Sunny Feng

Page Tools