Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
**[[:resources:tools-software:a2bv2:quickstartguide:hardware-setup | Click here to return to the Hardware Setup page]]**

====== AD242x standard power ======

===== Evaluation boards =====
The Evaluation boards used in the AD242x demos are explained in the following subsections.

==== EVAL-AD2428WD1BZ ====
[[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wd1bz|Figure 20]] shows an [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wd1bz|EVAL-AD2428WD1BZ]] board which can be used as either an A2B main or sub node. The board has following components
  * AD2428 A2B transceiver
  * ADAU1452 SigmaDSP Audio Processor
  * 512K Self-Boot Memory (EEPROM)
  * S/PDIF Optical Connectors
  * Codec ADAU1761

{{:resources:tools-software:a2bv2:quickstartguide:eval-ad2428wd1bz_board.png?300|}}

**Figure 20:** EVAL-AD2428WD1BZ board

=== Jumper Settings ===
== EVAL-AD2428WD1BZ without 1452 DSP Bypass ==

^ **Jumper** ^ **Action/Pin no** ^ **Comments** ^
|Used as main-node|||
| JP1 (A2B power) | Install | - |
| JP2 | Uninstall | Install when phantom power or hybrid power support is required |
| JP3 | Uninstall | Install when phantom power or hybrid power support is required |
| JP4 (BOOT)| Install | Self-Boot option disabled |
| JP5 (BCLK) | 3-4 | ADAU1452_BCLK_OUT0 -> AD2428_BCLK |
| JP6 (SYNC) | 3-4 | ADAU1452_LRCLK_OUT0 -> AD2428_SYNC |
| JP7 (DRX0) | 3-4 | ADAU1452_SDATA_OUT0 -> AD2428_DRX0 |
| JP8 (DRX1) | 2-3 | ADAU1452_SDATA_OUT1 -> AD2428_DRX1 If Secondary Rx data line DRX1 is desired. Uninstall if only primary data line DRX0 is required. |
| JP9 (DTX1) | 3-4 | AD2428_DTX1 -> ADAU1452_SDATA_IN1 If Secondary Tx data line DTX1 is desired. Uninstall if only primary data line DTX0 is required.|
| JP10 (DTX0) | 1-2 | AD2428_DTX0 -> ADAU1452_SDATA_IN0 |
| JP11 (ADMP621 CLK) | Uninstall | - |
| JP12 (NTC) | Install | - |
| JP13 (A2B_REG) | Uninstall | - |
| JP14 (VOLTAGE) | Uninstall | Install/ Uninstall depending on VIN requirement. \\ Installed -> VIN = 7V \\ Uninstalled -> VIN = 8V |
| JP19 (1961 BCLK) | 1-2 | ADAU1761 MCLK from CLKOUT of ADAU1452 |
| - | - | - |
| Used as sub-node |||
| JP1 (A2B power) | Install | - |
| JP2 | Uninstall | Install when phantom power or hybrid power support is required |
| JP3 | Uninstall | Install when phantom power or hybrid power support is required |
| JP4 (BOOT) | Install | Self-Boot option disabled |
| JP5 (BCLK) | 3-4-5 | AD2428_BCLK -> ADAU1452_BCLK_OUT0 & ADAU1452_BCLK_IN0 (Use a three-way wire connector – Figure 21) |
| JP6 (SYNC) | JP5(3-4) & JP7(5) | AD2428_SYNC -> ADAU1452_LRCLK_OUT0 & ADAU1452_LRCLK_IN0 |
| JP7 (DRX0) | 3-4 | ADAU1452_SDATA_OUT0 -> AD2428_DRX0 JP7.5 should be connected to SYNC signals on JP6.3 & JP6.4 (Use a three-way wire connector – Figure 21) |
| JP8 (DRX1) | 2-3 | ADAU1452_SDATA_OUT1 -> AD2428_DRX1 If Secondary Rx data line DRX1 is desired. Uninstall if only primary data line DRX0 is required. |
| JP9 (DTX1) | 3-4 | AD2428_DTX1 -> ADAU1452_SDATA_IN1 If Secondary Tx data line DTX1 is desired. Uninstall if only primary data line DTX0 is required. |
| JP10 (DTX0) | 1-2 | AD2428_DTX0 -> ADAU1452_SDATA_IN0 |
| JP11 (ADMP621 CLK) | Uninstall | - |
| JP12 (NTC) | Install | - |
| JP13 (A2B_REG) | Uninstall | - |
| JP14 (VOLTAGE) | Uninstall | Install depending on VIN requirement. \\ Installed -> VIN = 7V \\ Uninstalled -> VIN = 8V |
| JP19 (1961 BCLK) | 1-2 | ADAU1761 MCLK from CLKOUT of ADAU1452 |



{{:resources:tools-software:a2bv2:quickstartguide:three_way_jumper_connection.png?300|}}

**Figure 21:** Three way jumper connection

EVAL-AD2428WD1BZ with 1452 Without Bypass
^ **Jumper** ^ **Action/Pin no** ^ **Comments** ^
| Used as main-node |||
| JP1 (A2B power) | Install | - |
| JP2 | Uninstall | Install when phantom power or hybrid power support is required |
| JP3 | Uninstall |  |
| JP4 (BOOT) | Install | Self-Boot option disabled |
| JP5 (BCLK) | 3-4 | ADAU1452_BCLK_OUT0 -> AD2428_BCLK |
| JP6 (SYNC) | 3-4 | ADAU1452_LRCLK_OUT0 -> AD2428_SYNC |
| JP7 (DRX0) | 3-4 | ADAU1452_SDATA_OUT0 -> AD2428_DRX0 |
| JP8 (DRX1) | 2-3 | ADAU1452_SDATA_OUT1 -> AD2428_DRX1 If Secondary Rx data line DRX1 is desired. Uninstall if only primary data line DRX0 is required. |
| JP9 (DTX1) | 3-4 | AD2428_DTX1 -> ADAU1452_SDATA_IN1 If Secondary Tx data line DTX1 is desired. Uninstall if only primary data line DTX0 is required. |
| JP10 (DTX0) | 1-2 | AD2428_DTX0 -> ADAU1452_SDATA_IN0 |
| JP11 (ADMP621 CLK) | Uninstall | - |
| JP12 (NTC) | Install | - |
| JP13 (A2B_REG) | Uninstall | - |
| JP14 (VOLTAGE) | Uninstall | Install/ Uninstall depending on VIN requirement. \\ Installed -> VIN = 7V \\ Uninstalled -> VIN = 8V |
| JP19 (1961 BCLK) | 1-2 | ADAU1761 MCLK from CLKOUT of ADAU1452 |
| - | - | - |
| Used as sub-node |||
| JP1 (A2B power) | Install | - |
| JP2 | Uninstall | Install when phantom power or hybrid power support is required |
| JP3 | Uninstall | Install when phantom power or hybrid power support is required |
| JP4 (BOOT) | Install | Self-Boot option disabled |
| JP5 (BCLK) | 1-3 | AD2428_BCLK -> ADAU1961_BCLK |
| JP6 (SYNC) | 1-3 | AD2428_SYNC -> ADAU1961_LRCLK |
| JP7 (DRX0) | 1-3 | ADAU1961_ADC -> AD2428_DRX0 |
| JP8 (DRX1) | Uninstall | - |
| JP9 (DTX1) | Uninstall | - |
| JP10 (DTX0) | 2-3 | AD2428_DTX0 -> ADAU1961_DAC |
| JP11 (ADMP621 CLK) | Uninstall | - |
| JP12 (NTC) | install | - |
| JP13 (A2B_REG) | Uninstall | - |
| JP14 (VOLTAGE) | Uninstall | Install/ Uninstall depending on VIN requirement. \\ Installed -> VIN = 7V \\ Uninstalled -> VIN = 8V |
| JP19 (1961 BCLK) | 2-3 | ADAU1761 MCLK from AD2428_BCLK |







==== EVAL-AD2428WB1BZ ====
The [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wb1bz|Figure 22]] shows an [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wb1bz|EVAL-AD2428WB1BZ]] board which can be used as an A2B sub node. The board has following peripherals
  * AD2428 A2B transceiver
  * SigmaDSP with codec (ADAU1761).
  * 2 PDM Microphones
  * Push Button
  * EEPROM

{{:resources:tools-software:a2bv2:quickstartguide:eval-ad2428wb1bz_board.png?400|}}

**Figure 22:** EVAL-AD2428WB1BZ board

==== EVAL-AD2428WC1BZ ====
The [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wc1bz|Figure 23]] shows an [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#eval-ad2428wc1bz|EVAL-AD2428WC1BZ]] board which can be used as an A2B sub node. The board has following peripherals
  * AD2428 A2B transceiver
  * 4 PDM Microphones

{{:resources:tools-software:a2bv2:quickstartguide:eval-ad2428wc1bz_board.png?400|}}

**Figure 23:** EVAL-AD2428WC1BZ board

===== Connections =====
To run the sample demo, the following setup connections are to be made.

==== Bus power sub-nodes ====

=== Evaluation boards ===
A2B Evaluation boards shall be connected in the following order
  - EVAL-AD2428WD1BZ (Main) <–>EVAL-AD2428WC1BZ (Sub 0) <–> EVAL-AD2428WB1BZ (Sub 1) as shown in [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#bus_power_sub-nodes|Figure 24]]
  - Connect twisted-pair wire between the “B” connector on the Main board and the “A” connector on the Sub 0 board.
  - Connect twisted-pair wire between the “B” connector on the Sub 0 board and the “A” connector on the Sub 1 board.
  - Connect 12V power supply to the power connector (P4) on AD2428WD1BZ board.
<note>This connection is recommended for running the sample demo using PC as host. Refer Section 7 for more details on using BF27,ADSP-SC584,ADSP-SC573 as host processor.</note>

{{:resources:tools-software:a2bv2:quickstartguide:a2b_eval_board_connections_1.png?500|}}

**Figure 24:** A2B Eval board connections

=== USBi ===
  * Attach an USBi cable to the main board connector P1 as shown in [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#bus_power_sub-nodes|Figure 24]]. Other end of the cable should be connected to the PC.
  * This connection is required to override the schematic for the main node SigmaDSP ADAU1452. The connection is also used to directly control A2B system when PC is used as the target processor (no SDP-B board connected).

=== Audio In/out ===
  * Connect separate audio sources (e.g., output from an iPod) to ‘Audio Line- in’ ports, shown in [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#bus_power_sub-nodes|Figure 24]], on AD2428WD1BZ and AD2428WB1BZ boards.
  * Connect separate audio sinks (e.g., active speakers) to ‘Audio Line-out’ ports, shown in [[:resources:tools-software:a2bv2:quickstartguide:hardware-setup:ad242x-standard-power#bus_power_sub-nodes|Figure 24]], on AD2428WD1BZ and AD2428WB1BZ boards.
<note>Do not connect the audio source directly from PC toWB1BZ board as they can cause ground loop issues. If connected discovery will fail for WB1BZ and subsequent nodes.</note>

==== Local powered sub-nodes ====

{{:resources:tools-software:a2bv2:quickstartguide:ad2428wd1bz_boards.png?400|}}

**Figure 25:** Two local powered AD2428WD1BZ boards (One of the audio stream is shown here)

As per Figure 25 two local powered nodes can be connected to each other to form an A2B network. One of them is a main node and the other is a sub node. This figure represents one of the two audio stream configurations. Figure 26 and Figure 27 represent the audio configurations with and without bypassing the 1452 DSP respectively. Connect audio sources and sinks as per these two figures.

{{:resources:tools-software:a2bv2:quickstartguide:audio_routing_without_1452_dsp_bypass.png?250|}}

**Figure 26:** Audio routing without 1452 DSP bypass

{{:resources:tools-software:a2bv2:quickstartguide:audio_routing_with_1452_dsp_bypass.png?250|}}

**Figure 27:** Audio routing with 1452 DSP bypass
Analog Devices Wiki

Page Tools
