Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:tools-software:a2bv2:quickstartguide:appendix-a [09 Oct 2023 12:23] – agnes monicaresources:tools-software:a2bv2:quickstartguide:appendix-a [20 Dec 2023 12:19] (current) – [Network Properties] Gireesha Nirvanaiah
Line 20: Line 20:
       * EVAL- AD2438WD1BZ: This can be used as main node       * EVAL- AD2438WD1BZ: This can be used as main node
       * EVAL- AD2437A1NZ: This can be used as both a main and a sub node       * EVAL- AD2437A1NZ: This can be used as both a main and a sub node
-      * EVAL-AD2437B1NZ: This is a sub node only platform.+      * EVAL- AD2437B1NZ: This is a sub node only platform. 
 +      * EVAL- AD2437A1MZ: This can be used as both a main and a sub node. 
 +      * EVAL- AD2437B1MZ: This is a sub node only platform.
   - **A2BBusAnalyzer**   - **A2BBusAnalyzer**
     - **AD242x:** This can be used for Main/Sub Node Emulation or Bus Monitoring of 242x transceiver variants on the A2B Bus Analyzer Hardware     - **AD242x:** This can be used for Main/Sub Node Emulation or Bus Monitoring of 242x transceiver variants on the A2B Bus Analyzer Hardware
Line 33: Line 35:
   * Generic device: A device that takes an xml file as input for programming via I2C.   * Generic device: A device that takes an xml file as input for programming via I2C.
   * Non-Programmable generic device: A device that is used for representing not programmable peripherals in A2B system (e.g. Microphone).   * Non-Programmable generic device: A device that is used for representing not programmable peripherals in A2B system (e.g. Microphone).
-These devices are available as part of the toolbox once inside the platform view/canvas as shown in **Error! Reference source not found..** The platform canvas can be opened by double clicking on the platform in the system view or by clicking the “Canvas” option under the platform in the Project window.+These devices are available as part of the toolbox once inside the platform view/canvas as shown in below, the platform canvas can be opened by double clicking on the platform in the system view or by clicking the “Canvas” option under the platform in the Project window.
  
 ==== Transceiver settings (General View, Register View, Stream View and Crossbar View) ==== ==== Transceiver settings (General View, Register View, Stream View and Crossbar View) ====
Line 70: Line 72:
 **Modified:** All sub nodes are discovered and immediately initialized (for synchronous data exchange) sequentially from sub 0 to the last available sub node in the system. **Modified:** All sub nodes are discovered and immediately initialized (for synchronous data exchange) sequentially from sub 0 to the last available sub node in the system.
  
-**Optimized:** Even before a node is initialized the host tries to discover the next node. The time for the next node to be discovered is used to initialize the current node. Synchronous data can start only after all nodes are discovered and initialized (not supported for AD2430 AND AD2438).+**Optimized:** Even before a node is initialized the host tries to discover the next node. The time for the next node to be discovered is used to initialize the current node. Synchronous data can start only after all nodes are discovered and initialized.
  
 **Advanced:** Even before a node is initialized the host tries to discover the next node. The time for the next node to be discovered is used to initialize the current node. Synchronous data exchange can start as soon as a main and sub node 0 is initialized (not supported for AD243x main). **Advanced:** Even before a node is initialized the host tries to discover the next node. The time for the next node to be discovered is used to initialize the current node. Synchronous data exchange can start as soon as a main and sub node 0 is initialized (not supported for AD243x main).
Line 77: Line 79:
  
 The Line Fault settings allow user to enable fault diagnostic feature of the software. With this any line fault encountered in the system is handled and reported to the user. The Line Fault settings allow user to enable fault diagnostic feature of the software. With this any line fault encountered in the system is handled and reported to the user.
 +
 +**Override Bus Self Discovery:** If checked, Bus self-discovery status is ignored, discovery process starts with the soft-reset of A2B network. If unchecked, software looks for a self-discovered network, configures the network as per the schematic. 
  
 **Enable Line Fault Diagnostics:** Enables line fault diagnostic feature of software. When set, SigmaStudio+ will continuously monitor the network for faults at 1 second interval. Detected faults will be handled and notified. **Enable Line Fault Diagnostics:** Enables line fault diagnostic feature of software. When set, SigmaStudio+ will continuously monitor the network for faults at 1 second interval. Detected faults will be handled and notified.
resources/tools-software/a2bv2/quickstartguide/appendix-a.1696846984.txt.gz · Last modified: 09 Oct 2023 12:23 by agnes monica

Page Tools