Differences

This shows you the differences between two versions of the page.

--- resources:quick-start:adin1110_linux_quick_start_guide [05 Dec 2022 06:47] – Alexandru Tachici
+++ resources:quick-start:adin1110_linux_quick_start_guide [05 Dec 2022 06:55] – Alexandru Tachici
@@ Line 24: / Line 24: @@
 ADIN1110 needs to operate in Generic SPI mode (see Datasheet) and with CRC protection enabled. In order to do this find S201 and set every switch to the following table:
-^ SWTICH    ^ POSITION ^
+^ SWITCH    ^ POSITION ^
 | SPI_CFG0  | OFF |
 | SPI_CFG1  | ON  |
@@ Line 68: / Line 68: @@
 ADIN1110 needs to operate in Generic SPI mode (see Datasheet) and with CRC protection enabled. In order to do this find S201 and set every switch to the following table:
-^ SWTICH    ^ POSITION ^
+^ SWITCH    ^ POSITION ^
 | SPI_CFG0  | OFF |
 | SPI_CFG1  | ON  |
@@ Line 75: / Line 75: @@
 | MS_SEL    | OFF |
-Make sure IMX8MM-BB is set to boot from the SD Card, for more details go to [[https://www.nxp.com/document/guide/get-started-with-the-i-mx-8m-mini-evkb:GS-iMX-8M-Mini-EVK | Boot Swtich Setup]].
+Make sure IMX8MM-BB is set to boot from the SD Card, for more details go to [[https://www.nxp.com/document/guide/get-started-with-the-i-mx-8m-mini-evkb:GS-iMX-8M-Mini-EVK | Boot Switch Setup]].
@@ Line 235: / Line 235: @@
 In order to do this find S1 and set every switch to the following table:
-^ SWTICH    ^ POSITION ^
+^ SWITCH    ^ POSITION ^
 | SPI_CFG0  | ON |
 | SPI_CFG1  | ON  |
@@ Line 241: / Line 241: @@
 | TX2V4_DIS | OFF |
 | MS_SEL    | OFF |
-=== Board settings ===
-ADIN1110 needs to operate in Generic SPI mode (see Datasheet) and with CRC protection disabled. You may enable the CRC but that needs a change in the DT also.
-See [[https://github.com/analogdevicesinc/linux/blob/master/Documentation/devicetree/bindings/net/adi%2Cadin1110.yaml| adin1110.yaml]].
 == Getting your Jetson Nano flashed with the SDK Manager ==
@@ Line 316: / Line 310: @@
 | kernel/kernel-4.9/driver/drivers/net/ethernet/Makefile | Linux 4.9 ethernet Makefile with the necessary adjustments |
 | kernel/kernel-4.9/driver/drivers/net/ethernet/Kconfig | Linux 4.9 ethernet Kconfig with the necessary adjustments |
-| kernel/kernel-4.9/arch/arm64/configs/adi_tegra_defconfig | A modified tegra_defconfig with PHY + MAC + SWTICHDEV enabled |
+| kernel/kernel-4.9/arch/arm64/configs/adi_tegra_defconfig | A modified tegra_defconfig with PHY + MAC + SWITCHDEV enabled |
 | kernel/kernel-4.9/scripts/Kbuild.include | Original Kbuild.include with a small bugfix see [[ https://forums.developer.nvidia.com/t/failed-to-make-l4t-kernel-dts/116399/9 | here details ]] |
 | kernel/kernel-4.9/include/uapi/linux/types.h | Original types.h with a compile error fixed. |

Wiki

Analog Devices Wiki

Differences

Analog Devices Wiki

Differences

Page Tools