Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:fpga:xilinx:pmod:adxrs453_adxl345_lx9 [10 Dec 2012 15:57] – Download Wrapper Alexandru.Tofanresources:fpga:xilinx:pmod:adxrs453_adxl345_lx9 [29 Mar 2013 11:00] – [Running Demo (SDK) Program] Alexandru.Tofan
Line 15: Line 15:
 ==== Running Demo (SDK) Program ==== ==== Running Demo (SDK) Program ====
  
-<note tip>If you are not familiar with LX9 and/or Xilix tools, please visit\\ [[http://www.xilinx.com/products/boards-and-kits/AES-S6MB-LX9.htm]] for details. +<WRAP tip>If you are not familiar with LX9 and/or Xilix tools, please visit\\ [[http://www.xilinx.com/products/boards-and-kits/AES-S6MB-LX9.htm]] for details. 
-</note>+</WRAP>
  
-To begin, connect the PmodGYRO2 to J5 connector of LX9 board, pins 7 to 12 (see image below). You must use an extension cable or the [[http://digilentinc.com/Products/Detail.cfm?NavPath=2,401,549&Prod=PMOD-TPH|Pmod-TPH (Digilent)]].+To begin, connect the PmodGYRO2 to J5 connector of LX9 board, pins 7 to 12. You must use an extension cable or the [[http://digilentinc.com/Products/Detail.cfm?NavPath=2,401,549&Prod=PMOD-TPH|Pmod-TPH (Digilent)]]. Afterwards connect PmodACL to connector J4 of the LX9 Board (see image below).
  
 {{:resources:fpga:xilinx:pmod:gyro2_acl_lx9.jpg?300|Connecting Pmods to LX-9 MicroBoard}} {{:resources:fpga:xilinx:pmod:gyro2_acl_lx9.jpg?300|Connecting Pmods to LX-9 MicroBoard}}
Line 32: Line 32:
 On the LX-9 MicroBoard D10 and D9 display the Tap/Double Tap status. If you tap the device once, D10 will turn on for a short period of time. If you double tap the device, D10 and D9 will both turn on at the same time.\\ On the LX-9 MicroBoard D10 and D9 display the Tap/Double Tap status. If you tap the device once, D10 will turn on for a short period of time. If you double tap the device, D10 and D9 will both turn on at the same time.\\
  
-<note important>+<WRAP important>
   * Connecting the PmodGYRO2 must be done with an extension cable or a PmodTPH.   * Connecting the PmodGYRO2 must be done with an extension cable or a PmodTPH.
   * Connecting the PmodACL to the board with an extension cable provides ease of use.   * Connecting the PmodACL to the board with an extension cable provides ease of use.
   * UART must be set to 57600 baudrate.   * UART must be set to 57600 baudrate.
-</note>+</WRAP>
  
 ===== Downloads ===== ===== Downloads =====
resources/fpga/xilinx/pmod/adxrs453_adxl345_lx9.txt · Last modified: 09 Jan 2021 00:57 by Robin Getz

Page Tools