Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
resources:eval:user-guides:eval-adicup3029:reference_designs:demo_cn0415 [26 Feb 2019 23:11] – [Available commands] Add complete examples. Mark Thorenresources:eval:user-guides:eval-adicup3029:reference_designs:demo_cn0415 [05 Mar 2021 04:09] – [Obtaining the Source Code] adding in .Hex files Zuedmar Arceo
Line 66: Line 66:
 ===== Setting up the Hardware ===== ===== Setting up the Hardware =====
  
-  - Connect **EVAL-CN0415-ARDZ** board to the **EVAL-ADICUP3029**. {{ :resources:eval:user-guides:eval-adicup3029:reference_designs:cn0415_stacked_adicup3029.jpg?nolink | CN0415 stacked on ADICUP3029}}+  - Connect **EVAL-CN0415-ARDZ** board to the **EVAL-ADICUP3029**. {{ :resources:eval:user-guides:eval-adicup3029:reference_designs:cn0415_adicup3029_dock.jpeg | CN0415 docked on ADICUP3029 }}
   - Connect a micro-USB cable to **P10** connector of the **EVAL-ADICUP3029** and connect it to a computer.   - Connect a micro-USB cable to **P10** connector of the **EVAL-ADICUP3029** and connect it to a computer.
   - Connect a solenoid actuator to the **P8** connector with the positive wire on pin 1 and negative wire on pin 2.   - Connect a solenoid actuator to the **P8** connector with the positive wire on pin 1 and negative wire on pin 2.
-  - Connect a 12V power supply to the **P1** connector with the positive wire on pin 1 and negative wire on pin 2.{{ :resources:eval:user-guides:eval-adicup3029:reference_designs:powered_cn0415.jpg?nolink | Powered CN0415 board with solenoid}}+  - Connect a 12V power supply to the **P1** connector with the positive wire on pin 1 and negative wire on pin 2.{{ :resources:eval:user-guides:eval-adicup3029:reference_designs:cn0415_fully_connected.jpeg | CN0415 power up }}
   - Turn on power supply.   - Turn on power supply.
 ===== Configuring the Software ===== ===== Configuring the Software =====
Line 88: Line 88:
 ===== Outputting Data ===== ===== Outputting Data =====
  
-==== Serial Terminal Output ==== +{{page>/wiki/common#serial_terminal_setup&nofooter&noheader}}
- +
-The program outputs data and **CLI** interface to a serial terminal through **UART**. +
- +
-  - In order to view the data, you must flash the program to the EVAL-ADICUP3029. +
-  - Then follow the UART settings below with the serial terminal program. +
- +
-Following is the UART configuration. +
-    Select COM Port +
-    Baud rate: 115200 +
-    Data: 8 bit +
-    Parity: none +
-    Stop: 1 bit +
-    Flow Control: none +
-\\ +
-The terminal program must interpret new line as **LF** and **local echo** must be enabled.+
  
 ==== Available commands ==== ==== Available commands ====
Line 135: Line 120:
 {{ :resources:eval:user-guides:eval-adicup3029:reference_designs:wiki_pic.png?nolink | Terminal example}} {{ :resources:eval:user-guides:eval-adicup3029:reference_designs:wiki_pic.png?nolink | Terminal example}}
  
-===== Obtaining the Source Code =====+===== Obtaining the Software =====
  
-We recommend not opening the project directly, but rather import it into CrossCore Embedded Studios and make a local copy in your workspace. +There are two basic ways to program the ADICUP3029 with the software for the CN0415. 
 +  - Dragging and Dropping the .Hex to the Daplink drive 
 +  - Building, Compiling, and Debugging using CCES
  
-The source code and include files of the **ADuCM3029_demo_cn0415** can be found here:+Using the drag and drop method, the software is going to be a version that Analog Devices creates for testing and evaluation purposes.  This is the EASIEST way to get started with the reference design
  
-<WRAP round 80% download>+Importing the project into CrossCore is going to allow you to change parameters and customize the software to fit your needs, but will be a bit more advanced and will require you to download the CrossCore toolchain.  
  
-[[https://github.com/analogdevicesinc/EVAL-ADICUP3029/tree/master/projects/ADuCM3029_demo_cn0415 | AduCM3029_demo_cn0415 at Github]]+The software for the **ADuCM3029_demo_cn0415** can be found here: 
 + 
 +<WRAP round 80% download> 
 +Prebuilt CN0415 Hex File 
 +  * [[https://github.com/analogdevicesinc/EVAL-ADICUP3029/releases/download/Latest/ADuCM3029_demo_cn0415.hex| AduCM3029_demo_cn0415.Hex]] 
 +Complete CN0415 Source Files 
 +  * [[https://github.com/analogdevicesinc/EVAL-ADICUP3029/tree/master/projects/ADuCM3029_demo_cn0415| AduCM3029_demo_cn0415 Source Code]]
    
 </WRAP> </WRAP>
resources/eval/user-guides/eval-adicup3029/reference_designs/demo_cn0415.txt · Last modified: 19 Aug 2021 07:12 by erbe reyta

Page Tools