Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
====== EVAL-CN0418-ARDZ Shield Overview ======

The circuit shown in Figure 1 provides a complete, fully isolated and highly flexible, 4-channel analog output system suitable for programmable logic controllers (PLCs) and distributed control system (DCS) applications that require ±5 V, ±10 V voltage and  4 mA to 20 mA current output with HART-compatibility.   All outputs are protected from transients and are suitable for the most harsh industrial environments. 

The HART compatibility of this module provides a complete field communications solution that is simple to use, low cost, and extremely reliable.

The circuit is powered from a standard 24 V bus supply, with on-board filtering and protection circuitry. Because many factories and industrial environments power their PLC/DCS from a 24 V standard bus line, this module is easy to integrate into any existing system. This module can also be powered from other standard supplies, starting from 12 VDC to 28 VDC



This user guide will discuss how to use the [[adi>EVAL-ADICUP3029|EVAL-EVAL-ADICUP3029]] and evaluation software to configure and collect data from the [[adi>CN0418|EVAL-CN0418-ARDZ Evaluation Board]] **(CN-0418 Board)**.



{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:cn0418_board_images_rev_b.png?nolink&600 |}}


======EVAL-CN0418-ARDZ attached to EVAL-ADICUP3029======


{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:cn0418_crop.jpg?nolink |}}






====== Simplified functional block diagram ======


{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:latest_functional_block_diagram.png?nolink |}}
\\


===== General Setup =====
==== Equipment ====

  * [[adi>CN0418|EVAL-CN0418-ARDZ Evaluation Board]]
  * [[adi>EVAL-ADICUP3029|EVAL-ADICUP3029 Base Board]]
  * PC with a USB port and Windows 7 (32-bit) or higher 
  * Serial Terminal Software (Putty/TeraTerm or similar)
  * DC Power Supply (+12 V to +24 V / 1 A) or equivalent bench supply (optional)
  * Precision voltage and current source (for output measurement)
  * USB type A to micro USB type A cable
  * CN0418 Evaluation Software
{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:board_set_up_of_cn0418_and_adicup3029.png?1000|}}

  * The [[adi>CN0418|EVAL-CN0418-ARDZ]] **(CN-0418 Board)** connects to the [[adi>EVAL-ADICUP3029|EVAL-ADICUP3029]] **(ADICUP3029 Board)**
  * The [[adi>EVAL-ADICUP3029|EVAL-ADICUP3029]] **(ADICUP3029 Board)** connects to the PC via the USB cable.
  * Terminal block **P1** is the power supply input (input:+24V DC)
  * Terminal blocks **P6** provide the quad channel voltage output (-10V to +10V), and Current output (0mA to 24mA) and standard 4 mA to 20 mA HART compatible current inputs.

==== Power Supply Considerations and Configuration (P1) ====

Terminal block **P17** is the power supply input (input range:+12V to +36V DC). The EARTH terminal can be connected to an external earth connection, to the GND terminal or left floating if an external earth connection is not used. The Green power LED should lit up when connected to a power supply.


{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:power_led_and_connector.png?nolink}}



==== Default Shunt Jumper (P9 and P10) and DIP Switches (S3 and S4) Configuration ====
The default jumper position for **P9** and **P10** are shorted at position 1 and 2 while the two DIP switches **S3** and **S4** should be in **ON state** switch position.
{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:deffault_switches.png?nolink&600 |}}
^ P9 jumper connections for HART enable (EN) control ^^^ P10 jumper connections for  Chip select (SYNC) control ^^^
===Single board===
If only a single board is used, then connect jumpers P9 and P10 as shown in the table below.
^ Position ^ Description ^ Mode ^ Position ^ Description ^ Mode ^
| pin 1 & pin 2 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:hart_selection_single_j.png|}} | skip decoder | single{{ :resources:eval:user-guides:eval-adicup3029:hardware:hart_selection_single.png |}} | pin 1 & pin 2 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:dac_selection_single_j.png|}} | skip decoder | single {{ :resources:eval:user-guides:eval-adicup3029:hardware:cs_selection_single.png |}} |
===Multi board===
If more than one board is stacked (up to 4), then each board must be set to a different DAC and HART select address. Connect jumpers P9 and P10 as shown in the table below, and ensure that the software is configured accordingly. On a given board, set the DAC and HART address to the same position. If necessary, the software can be changed to address differently the DAC and HART on a given board.
^ Position ^ Description ^ Mode ^ Position ^ Description ^ Mode ^
| pin 4 & pin 6 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:hart_selection_multi_0_j.png|}} | AIN2:AIN3 = 00 | multiple{{ :resources:eval:user-guides:eval-adicup3029:hardware:hart_selection_multi_0.png |}} | pin 4 & pin 6{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:dac_selection_multi_0_j.png |}} | AIN0:AIN1 = 00 | multiple {{ :resources:eval:user-guides:eval-adicup3029:hardware:cs_selection_multi_0.png |}} |
| pin 3 & pin 5 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:hart_selection_multi_1_j.png|}} | AIN2:AIN3 = 01 | multiple {{ :resources:eval:user-guides:eval-adicup3029:hardware:hart_selection_multi_1.png |}} | pin 3 & pin 5{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:dac_selection_multi_1_j.png |}} | AIN0:AIN1 = 01 | multiple {{ :resources:eval:user-guides:eval-adicup3029:hardware:cs_selection_multi_1.png |}} |
| pin 7 & pin 5 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:hart_selection_multi_2_j.png|}} | AIN2:AIN3 = 10 | multiple {{ :resources:eval:user-guides:eval-adicup3029:hardware:hart_selection_multi_2.png |}} | pin 7 & pin 5{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:dac_selection_multi_2_j.png |}} | AIN0:AIN1 = 10 | multiple {{:resources:eval:user-guides:eval-adicup3029:hardware:cs_selection_multi_2.png |}} |
| pin 8 & pin 6 {{:resources:eval:user-guides:circuits-from-the-lab:cn0418:hart_selection_multi_3_j.png|}} | AIN2:AIN3 = 11 | multiple {{ :resources:eval:user-guides:eval-adicup3029:hardware:hart_selection_multi_3.png |}} | pin 8 & pin 6{{:resources:eval:user-guides:circuits-from-the-lab:cn0418:dac_selection_multi_3_j.png |}} | AIN0:AIN1 = 11 | multiple {{:resources:eval:user-guides:eval-adicup3029:hardware:cs_selection_multi_3.png |}} |

==== Default EEPROM Address configuration of Solder Jumper position JP2, JP3 and JP4 ====
EEPROM default address configuration of the board is "000" you can configure the EEPROM I2C address from 000 to 111.

{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:eeprom_default_address.png?nolink&600 |}}



==== Default EEPROM WP ( Write Protect) mode configuration of Solder Jumper JP1 ====
EEPROM **WP** pin can be configured as single or multi board operation. The default connection of **WP** pin is shorted to GND.

{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:eeprom_wp_mode.png?nolink&600 |}}
^ JP1 soldering position ^^
^ Position ^ Description ^
| pin 2 & pin 3 {{ :resources:eval:user-guides:eval-adicup3029:hardware:jp1_s.png?60 |}} | enable write protection (WP) (single board operation by default) {{ :resources:eval:user-guides:eval-adicup3029:hardware:jp1_s_d.png?130 |}} |
| pin 2 & pin 1 {{ :resources:eval:user-guides:eval-adicup3029:hardware:jp1_m.png?60 |}} | control write protection (WP) (multi board operation) {{ :resources:eval:user-guides:eval-adicup3029:hardware:jp1_m_d.png?130 |}} |

==== 16 bit Voltage and Current Analog Output Connection (P6) ====
{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:cn0418_output_terminals.png?nolink&600 |}}



====Peripheral Connectors ====

All connector pinouts for the EVAL-CN0418-ARDZ are described in the table below. 

^ Connector         ^ Pin No. ^ Pin Name ^ ADuCM3029 Pin Function             ^ CN0418 Pin Function  ^
^ Arduino DIO High  | 1       | SCL      | I2C0_SCL/GPIO04                    | SCL (EEPROM)              |
| :::               | 2       | SDA      | I2C0_SDA/GPIO05                    | SDA (EEPROM)              |
| :::               | 3       | AREF     | VREF+                              | NC                        |
| :::               | 4       | AGND     | AGND (Analog ground)               | DGND                      |
| :::               | 5       | SCLK     | SPI0_CLK/SPT0_BCLK/GPIO00          | DAC_SCLK (AD5755-1)       |
| :::               | 6       | MISO     | SPI0_MISO/SPT0_BD0/GPIO02          | DAC_MISO_BUFF (AD5755-1)  |
| :::               | 7       | MOSI     | SPI0_MOSI/SPT0_BFS/GPIO01          | DAC_MOSI (AD5755-1)       |
| :::               | 8       | CS       | SPI0_CS1/SYS_CLKIN/SPI1_CS3/GPIO26 | DAC_SYNC(AD5755-1)        |
| :::               | 9       | RDY      | SPI0_RDY/GPIO30                    | HART_MULT_A0(AD5700-1)    |
| :::               |10       | IO28     | GPIO28                             | HART_MUL_A1(AD5700-1)     |
^ Arduino DIO Low   | 1       | IO08     | BPR0_TONE_N/GPIO08                 | DAC_FAULT(AD5755-1)       |
| :::               | 2       | IO27     | TMR1_OUT/GPIO27                    | AD5700_RTS (AD5700-1)     |
| :::               | 3       | IO33     | XINT0_WAKE3/TMR2_OUT/GPIO33        | AD5700_CD_BUFF(AD5700-1)  |
| :::               | 4       | IO09     | BPR0_TONE_P/SPI2_CS1/GPIO09        | SW_TXD (AD5700-1)         |
| :::               | 5       | IO13     | XINT0_WAKE2/GPIO13                 | HW RXD (AD5700-1)         |
| :::               | 6       | IO15     | XINT0_WAKE0/GPIO15                 | NC                        |
| :::               | 7       | TX       | UART0_TX/GPIO10                    | NC                        |
| :::               | 8       | RX       | UART0_RX/GPIO11                    | NC                        |
^ Arduino Analog    | 1       | AIN0     | ADC0_VIN0/GPIO35                   | HART_COM_A0               |
| :::               | 2       | AIN1     | ADC0_VIN1/GPIO36                   | HART_COM_A1               |
| :::               | 3       | AIN2     | ADC0_VIN2/GPIO37                   | DAC_COM_A0                |
| :::               | 4       | AIN3     | ADC0_VIN3/GPIO38                   | DAC_COM_A1                |
| :::               | 5       | AIN4     | ADC0_VIN4/SPI2_CS3/GPIO39          | NC                        |
| :::               | 6       | AIN5     | ADC0_VIN5/SPI0_CS2/GPIO40          | NC                        |
^ Arduino Power     | 1       | NC       | - not connected -                  | NC                        |
| :::               | 2       | IOREF    | +3.3V                              | IO_VREF (+3V3)                   |
| :::               | 3       | RESET    | SYS_HWRST_N                        | NC                        |
| :::               | 4       | 3.3V     | +3.3V                              | NC                        |
| :::               | 5       | 5V       | +5V                                | 5V                        |
| :::               | 6       | GND      | DGND (Digital Ground)              | GND                       |
| :::               | 7       | GND      | DGND (Digital Ground)              | GND                       |
| :::               | 8       | Vin      | DC Barrel Jack Power +7V to +12V   | +7.5V                     |



\\
===== Advanced Setup =====
Up to four EVAL-CN0418-ARDZ boards can be controlled by a single Arduino or EVAL-ADICUP3029 base board by using a simple control scheme. This control scheme will control the SYNC, CD and RX signals to avoid a data conflict.

{{ :resources:eval:user-guides:circuits-from-the-lab:cn0418:cn0418_multiple_connection.png |}}

\\
===== More Information and Useful Links =====
  * [[https://github.com/analogdevicesinc/EVAL-ADICUP3029/tree/master/projects/ADuCM3029_demo_cn0418|CN0418 Evaluation Software]]
  * [[ADI>CN0418|CN0418 Circuit Note Page]]
  * [[ADI>CN0418-DesignSupport|CN0418 Design Support Package]]
  * [[ADI>AD5755-1|AD5755-1 Product Page]]
  * [[ADI>AD5700-1|AD5700-1 Product Page]]
  * [[ADI>ADUM3482|ADUM3482 Product Page]]
  * [[ADI>ADUM3151|ADUM3151 Product Page]]
  * [[ADI>ADP2441|ADP2441 Product Page]]
  * [[ADI>ADG704|ADG704 Product Page]]
  * [[ADI>LT8301|LT8301 Product Page]]





====== Schematic, PCB Layout, Bill of Materials ======
<WRAP round 80% download>

[[adi>cn0418-designsupport|EVAL-CN0418-ARDZ Design & Integration Files]]
  * Schematics 
  * PCB Layout 
  * Bill of Materials 
  * Allegro Project

</WRAP>
====== Software ======
  * [[resources:eval:user-guides:eval-adicup3029:reference_designs:demo_cn0418|ADICUP3029 + CN0418 Demo]]

=====Registration===== 
<WRAP round tip 80% >
Receive software update notifications, documentation updates, view the latest videos, and more when you register your hardware.  [[reg>EVAL-CN0418-ARDZ?&v=RevC|Register]] to receive all these great benefits and more!
</WRAP>

// End of Document //
Analog Devices Wiki

Page Tools
