Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revisionBoth sides next revision
resources:eval:user-guides:circuits-from-the-lab:cn0511 [09 Aug 2022 23:05] – streamlining the software section Brandon Busheyresources:eval:user-guides:circuits-from-the-lab:cn0511 [10 Aug 2022 23:01] – updated figure numbers Brandon Bushey
Line 47: Line 47:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:clock_source.png?800 |Figure 5. EVAL-CN0511-RPIZ Clock Source Schematic Diagram}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:clock_source.png?800 |Figure 5. EVAL-CN0511-RPIZ Clock Source Schematic Diagram}}
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 5. EVAL-CN0511-RPIZ Clock Source Schematic Diagram</fc>//+//<fc #c0c0c0>Figure 3. EVAL-CN0511-RPIZ Clock Source Schematic Diagram</fc>//
 </wrap> </wrap>
  
Line 65: Line 65:
  
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 8. RF Output and Optional External Clock Input Connections</fc>//+//<fc #c0c0c0>Figure 4. RF Output and Optional External Clock Input Connections</fc>//
 </wrap> </wrap>
  
Line 73: Line 73:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:heat_sink_v2.jpg?600 |Cooling Management Guide of CN0511}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:heat_sink_v2.jpg?600 |Cooling Management Guide of CN0511}}
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 9. CN0511 Fan and Thermal Management</fc>//+//<fc #c0c0c0>Figure 5. CN0511 Fan and Thermal Management</fc>//
 </wrap> </wrap>
  
Line 81: Line 81:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:cn0511_power_supply_options.png?600 |Input Power Supply Connection Options of CN0511}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:cn0511_power_supply_options.png?600 |Input Power Supply Connection Options of CN0511}}
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 7. CN0511 Input Power Supply Connection Options</fc>//+//<fc #c0c0c0>Figure 6. CN0511 Input Power Supply Connection Options</fc>//
 </wrap> </wrap>
  
Line 106: Line 106:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:eval-cn0511_test_block_diagram.jpg?500 |Figure 3. Test Setup Functional Block Diagram}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:eval-cn0511_test_block_diagram.jpg?500 |Figure 3. Test Setup Functional Block Diagram}}
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 3. Functional System Block Diagram</fc>//+//<fc #c0c0c0>Figure 7. Functional System Block Diagram</fc>//
 </wrap> </wrap>
  
Line 112: Line 112:
  
 To set up the complete system, follow these steps: To set up the complete system, follow these steps:
-  - Connect the EVAL-CN0511-RPIZ to the Raspberry Pi through the 40-pin connector.{{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:cn0511_rpi_v1.jpg?600 |Figure 7. Hardware Connection of EVAL-CN0511-RPIZ and Raspberry Pi 3 Model B+}}<wrap center 50%>//<fc #c0c0c0>Figure 7. Hardware Connection of EVAL-CN0511-RPIZ and Raspberry Pi 3 Model B+</fc>//</wrap>+  - Connect the EVAL-CN0511-RPIZ to the Raspberry Pi through the 40-pin connector.{{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:cn0511_rpi_v1.jpg?600 |Figure 8. Hardware Connection of EVAL-CN0511-RPIZ and Raspberry Pi 3 Model B+}}<wrap center 50%>//<fc #c0c0c0>Figure 8. Hardware Connection of EVAL-CN0511-RPIZ and Raspberry Pi 3 Model B+</fc>//</wrap>
   - Burn the SD card with the proper Analog Devices, Inc. Kuiper Linux image. Insert the burned SD card on the designated slot on the Raspberry Pi.   - Burn the SD card with the proper Analog Devices, Inc. Kuiper Linux image. Insert the burned SD card on the designated slot on the Raspberry Pi.
   - Connect the system to a monitor using an HDMI cable through the mini HDMI connector on the Raspberry Pi.   - Connect the system to a monitor using an HDMI cable through the mini HDMI connector on the Raspberry Pi.
Line 122: Line 122:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:sample_setup_v2.jpg?600 |CN0511 System Setup}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0511:sample_setup_v2.jpg?600 |CN0511 System Setup}}
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 10. CN0511 System Setup</fc>//+//<fc #c0c0c0>Figure 9. CN0511 System Setup</fc>//
 </wrap> </wrap>
  
Line 171: Line 171:
  
 <wrap center 50%> <wrap center 50%>
-//<fc #c0c0c0>Figure 11. Graphical User Interface (GUI) window of ADI IIO Oscilloscope with CN0511 Plug-in</fc>//+//<fc #c0c0c0>Figure 10. Graphical User Interface (GUI) window of ADI IIO Oscilloscope with CN0511 Plug-in</fc>//
 </wrap> </wrap>
  
resources/eval/user-guides/circuits-from-the-lab/cn0511.txt · Last modified: 26 Apr 2023 01:14 by erbe reyta

Page Tools