Differences

This shows you the differences between two versions of the page.

--- resources:eval:user-guides:circuits-from-the-lab:cn0326 [05 May 2015 19:41] – formatting Brandon Bushey
+++ resources:eval:user-guides:circuits-from-the-lab:cn0326 [03 Jan 2021 21:55] – fix links Robin Getz
@@ Line 10: / Line 10: @@
 ===== GENERAL SETUP =====
-  * [[http://www.analog.com/EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]] Evaluation Board
+  * [[adi>EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]] Evaluation Board
-  * [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Evaluation Board
+  * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Evaluation Board
-  * [[http://www.analog.com/SDP-PMD-IB1Z|SDP-PMD-IB1Z]] Evaluation Board
+  * [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]] Evaluation Board
   * [[ftp://ftp.analog.com/pub/cftl/CN0326|CN0326 Evaluation Software]]
     * (supplied with provided CD in kit)
@@ Line 44: / Line 44: @@
 {{:resources:eval:user-guides:circuits-from-the-lab:cn0326:cn0326fig11.jpg|}}
-  - Connect the 120-pin connector of the [[http://www.analog.com/SDP-PMD-IB1Z|SDP-PMD-IB1Z]] circuit board to the connector marked “CON A” on the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation (SDP) board.  Nylon hardware should be used to firmly secure the two boards, using the holes provided at the ends of the 120-pin connectors.
+  - Plug the mini end of the USB cable into connector J1 of the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] and connect the other end of the USB cable into the Laptop or PC.
-  - Populate a jumper across JP1 to give +3.3V voltage out in PMOD terminal as seen in the label found in [[http://www.analog.com/SDP-PMD-IB1Z|SDP-PMD-IB1Z]].
+    * Make sure that the computer installs the device drivers, and that you can see the //ADI Development Tools// in your computer's device manager.{{ :resources:eval:user-guides:circuits-from-the-lab:pulsar_pmod:device_manager.png?500 |}}
-  - Connect the 12-pin right angle male pin header of [[http://www.analog.com/EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]] to the 12-pin right angle female pin header of [[http://www.analog.com/SDP-PMD-IB1Z|SDP-PMD-IB1Z]].
+  - Remove the jumper across JP1 found on the [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]].
-  - Connect the pH probe in J1 of [[http://www.analog.com/EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]].
+  - Connect the 120-pin connector of the [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]] circuit board to the connector marked “CON A” on the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation (SDP) board.  Nylon hardware should be used to firmly secure the two boards, using the holes provided at the ends of the 120-pin connectors.
-  - Connect the RTD sensor in P1 of [[http://www.analog.com/EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]].
+  - Connect the EVAL-CFTL-6V-PWRZ to **J1** barrel jack of the [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]], and **WAIT 10 SECONDS** before continuing
-  - Plug the mini end of the USB cable into connector J1 of the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] and connect the other end of the USB cable into the Laptop or PC.
+  - Connect the 12-pin right angle male pin header of [[adi>EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]] to the 12-pin right angle female pin header of [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]].
-  - Plug in the wall wart and connect it to connector J1 of the [[http://www.analog.com/SDP-PMD-IB1Z|SDP-PMD-IB1Z]].
+  - Connect the pH probe in J1 of [[adi>EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]].
+  - Connect the RTD sensor in P1 of [[adi>EVAL-CN0326-PMDZ|EVAL-CN0326-PMDZ]].
+  - Place the jumper across JP1 on the [[adi>SDP-PMD-IB1Z|SDP-PMD-IB1Z]] and make sure it's positioned to +3.3V.
+  - Check again in the device manager to make sure the //ADI Development Tools// are still displaying.  If yes, then you'll be able to proceed onto the evaluation software section.  If you don't see ADI Development Tools, than you will have to start the hardware evaluation procedure over at step 1.{{ :resources:eval:user-guides:circuits-from-the-lab:pulsar_pmod:device_manager.png?500 |}}
 ----

Wiki

Analog Devices Wiki

Differences

Analog Devices Wiki

Differences

Page Tools