Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| resources:eval:user-guides:circuits-from-the-lab:cn0240 [04 Dec 2017 03:28] – update Trisha Cabildo | resources:eval:user-guides:circuits-from-the-lab:cn0240 [03 Jan 2021 21:55] – fix links Robin Getz | ||
|---|---|---|---|
| Line 16: | Line 16: | ||
| ===== Required Equipment ===== | ===== Required Equipment ===== | ||
| * [[adi> | * [[adi> | ||
| - | * [[http:// | + | * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**) |
| * [[ftp:// | * [[ftp:// | ||
| * Power Supply | * Power Supply | ||
| Line 33: | Line 33: | ||
| {{ : | {{ : | ||
| - | * The [[http:// | + | * The [[adi>EVAL-CN0240-SDPZ|EVAL-CN0240-SDPZ]] **(CN-0240 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector |
| - | * The [[http:// | + | * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable. |
| * Terminal block **J1** is the SDP connector | * Terminal block **J1** is the SDP connector | ||
| * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | ||
| Line 50: | Line 50: | ||
| {{ : | {{ : | ||
| - | - Connect the 120-pin connector on the [[adi> | + | - Connect the 120-pin connector on the [[adi> |
| - Connect a shunt resistor across the J4 input terminals with a load to ground as indicated in figure above | - Connect a shunt resistor across the J4 input terminals with a load to ground as indicated in figure above | ||
| - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | ||
| Line 97: | Line 97: | ||
| \\ | \\ | ||
| + | ==== Running the System ==== | ||
| + | -Open the CN0240.exe application from the default installation location | ||
| + | -Set the correct connector and click the Connect Button | ||
| + | -Upon successful connection, set the desired input signal parameters such as shunt voltage | ||
| + | -Start and control data acquisition through the data acquisition control buttons | ||
| + | -Output data will be shown in the graph. Edit graph through plot options and check boxes provided | ||
| + | -Click Disconnect if finished | ||
| + | -Click Quit to exit the program | ||
| + | \\ | ||
| ---- | ---- | ||
| Line 102: | Line 111: | ||
| * [[ftp:// | * [[ftp:// | ||
| * [[ADI> | * [[ADI> | ||
| - | * [[http:// | + | * [[adi>media/ |
| * [[ADI> | * [[ADI> | ||
| * [[ADI> | * [[ADI> | ||
| Line 113: | Line 122: | ||
| <WRAP round 80% download> | <WRAP round 80% download> | ||
| - | [[http:// | + | [[adi>media/ |
| * Schematics | * Schematics | ||
| * PCB Layout | * PCB Layout | ||
resources/eval/user-guides/circuits-from-the-lab/cn0240.txt · Last modified: 30 Jul 2021 07:24 by Victor Calinao, Jr