Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:circuits-from-the-lab:cn0218 [28 Nov 2017 01:00] – update eval software Trisha Cabildoresources:eval:user-guides:circuits-from-the-lab:cn0218 [30 Jul 2021 07:22] (current) – Victor Calinao, Jr
Line 15: Line 15:
 ===== Required Equipment ===== ===== Required Equipment =====
   * [[adi>EVAL-CN0218-SDPZ|EVAL-CN0218-SDPZ Evaluation Board]]   * [[adi>EVAL-CN0218-SDPZ|EVAL-CN0218-SDPZ Evaluation Board]]
-  * [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)+  * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)
   * [[ftp://ftp.analog.com/pub/cftl/CN0218/|CN0218 Evaluation Software]]   * [[ftp://ftp.analog.com/pub/cftl/CN0218/|CN0218 Evaluation Software]]
   * Power Supply   * Power Supply
Line 29: Line 29:
 ==== Block assignments ==== ==== Block assignments ====
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:8.png?nolink&550 |}}\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:8.png?nolink&550 |}}\\
-  * The [[http://www.analog.com/EVAL-CN0150-SDPZ|EVAL-CN0150-SDPZ]] **(CN-0150 Board)** connects to the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector +  * The [[adi>EVAL-CN0150-SDPZ|EVAL-CN0150-SDPZ]] **(CN-0150 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector 
-  * The [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable.+  * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable.
   * Terminal block **J1** is the SDP connector   * Terminal block **J1** is the SDP connector
   * Terminal block **J2** is the +6 V barrel connector for wall wart supply input   * Terminal block **J2** is the +6 V barrel connector for wall wart supply input
Line 42: Line 42:
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:9.png?nolink&600 |}}\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:9.png?nolink&600 |}}\\
  
-  - Connect the 120-pin connector on the [[adi>EVAL-CN0218-SDPZ|EVAL-CN0218-SDPZ Evaluation Board]] to the connector marked “CON A” on the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation (SDP) board+  - Connect the 120-pin connector on the [[adi>EVAL-CN0218-SDPZ|EVAL-CN0218-SDPZ Evaluation Board]] to the connector marked “CON A” on the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation (SDP) board
   - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above   - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above
   - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board   - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board
Line 71: Line 71:
   - **Connect** Button - Starts the connection between the [[ADI>CN0218|CN0218 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]].   - **Connect** Button - Starts the connection between the [[ADI>CN0218|CN0218 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]].
   - **Reset and Disconnect** - Resets the board and ends the connection between the [[ADI>CN0218|CN0218 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]]   - **Reset and Disconnect** - Resets the board and ends the connection between the [[ADI>CN0218|CN0218 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]]
-  - **Stop** Button -  Stop the program of CN0218 Evaluation Board +  - **Stop** Button - Stop collecting data from the CN0218 Board 
-  - **Test Setup** Tab - Shows the acquired measurement data in terms of ADC codes with respect to the samples\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:14.png?nolink&600 |}}+  - **Test Setup** Tab - Shows the acquired measurement data in terms of shunt voltage with respect to the samples\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:14.png?nolink&600 |}}
       * **Shunt Voltage** - Shunt voltage measurement output from ADC       * **Shunt Voltage** - Shunt voltage measurement output from ADC
       * **Click to Start Sampling** - Starts acquisition of measurement data       * **Click to Start Sampling** - Starts acquisition of measurement data
-      * **Clear Data** - Clears the current measurement data +      * **Clear Data** - Clear all data collected from the chart history 
       * **Save Data to File** - Save measurement data to file       * **Save Data to File** - Save measurement data to file
   - **Configure** Tab\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:15.png?nolink&600 |}}   - **Configure** Tab\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:15.png?nolink&600 |}}
       * **Flash LED** - Flashes the LED on the SDP controller board       * **Flash LED** - Flashes the LED on the SDP controller board
       * **Read Firmware** - Reads the firmware of CN0218 Evaluation Board        * **Read Firmware** - Reads the firmware of CN0218 Evaluation Board 
-  - **Plot** Options -  Edit plot display and options like interpolation and colors of waveform plot \\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:18.png?nolink&600 |}}+  - **Plot** Options -  Edit plot display and options like interpolation and color of output waveform \\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0218:18.png?nolink&600 |}}
 \\ \\
  
 +==== Running the System ====
 +  -Open the CN0218.exe application from the default installation location
 +  -Click the Connect Button
 +  -Upon successful connection, start and control data acquisition through the data acquisition control buttons
 +  -Output data will be shown in the graph. Edit graph through plot options and check boxes provided
 +  -Click Disconnect if finished
 +  -Click Quit to exit the program
 ---- ----
  
Line 88: Line 95:
   * [[ftp://ftp.analog.com/pub/cftl/CN0218/|CN0218 Evaluation Software]]   * [[ftp://ftp.analog.com/pub/cftl/CN0218/|CN0218 Evaluation Software]]
   * [[ADI>CN0218|CN0218 Circuit Note Page]]   * [[ADI>CN0218|CN0218 Circuit Note Page]]
-  * [[http://www.analog.com/media/en/reference-design-documentation/design-integration-files/CN0218-DesignSupport.zip|CN0218 Design Support Package]]+  * [[adi>media/en/reference-design-documentation/design-integration-files/CN0218-DesignSupport.zip|CN0218 Design Support Package]]
   * [[ADI>AD8212|AD8212 Product Page]]   * [[ADI>AD8212|AD8212 Product Page]]
   * [[ADI>AD7171|AD7171 Product Page]]   * [[ADI>AD7171|AD7171 Product Page]]
Line 98: Line 105:
  
 <WRAP round 80% download> <WRAP round 80% download>
-[[http://www.analog.com/media/en/reference-design-documentation/design-integration-files/CN0218-DesignSupport.zip|EVAL-CN0218-SDPZ Design & Integration Files]]+[[adi>media/en/reference-design-documentation/design-integration-files/CN0218-DesignSupport.zip|EVAL-CN0218-SDPZ Design & Integration Files]]
   * Schematics    * Schematics 
   * PCB Layout    * PCB Layout 
Line 104: Line 111:
   * PADS project   * PADS project
 </WRAP> </WRAP>
 +
 +=====Registration===== 
 +<WRAP round tip 80% >
 +Receive software update notifications, documentation updates, view the latest videos, and more when you register your hardware.  [[reg>EVAL-CN0218-SDPZ?&v=Rev A|Register]] to receive all these great benefits and more!</WRAP>
  
 //End of Document// //End of Document//
  
resources/eval/user-guides/circuits-from-the-lab/cn0218.1511827257.txt.gz · Last modified: 28 Nov 2017 01:00 by Trisha Cabildo

Page Tools