Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| resources:eval:user-guides:circuits-from-the-lab:cn0218 [03 Nov 2017 05:05] – update Trisha Cabildo | resources:eval:user-guides:circuits-from-the-lab:cn0218 [03 Jan 2021 21:56] – fix links Robin Getz | ||
|---|---|---|---|
| Line 15: | Line 15: | ||
| ===== Required Equipment ===== | ===== Required Equipment ===== | ||
| * [[adi> | * [[adi> | ||
| - | * [[http:// | + | * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**) |
| * [[ftp:// | * [[ftp:// | ||
| * Power Supply | * Power Supply | ||
| Line 29: | Line 29: | ||
| ==== Block assignments ==== | ==== Block assignments ==== | ||
| {{ : | {{ : | ||
| - | * The [[http:// | + | * The [[adi>EVAL-CN0150-SDPZ|EVAL-CN0150-SDPZ]] **(CN-0150 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector |
| - | * The [[http:// | + | * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable. |
| * Terminal block **J1** is the SDP connector | * Terminal block **J1** is the SDP connector | ||
| * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | ||
| Line 42: | Line 42: | ||
| {{ : | {{ : | ||
| - | - Connect the 120-pin connector on the [[adi> | + | - Connect the 120-pin connector on the [[adi> |
| - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above | - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above | ||
| - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | ||
| Line 53: | Line 53: | ||
| \\ | \\ | ||
| <WRAP center round important 60%> | <WRAP center round important 60%> | ||
| - | Do **not** connect | + | Connect the **system ground** and the **PCB isolated ground** |
| </ | </ | ||
| \\ | \\ | ||
| Line 61: | Line 61: | ||
| - Click **Next** to view the installation review page\\ \\ {{: | - Click **Next** to view the installation review page\\ \\ {{: | ||
| - Click **Next** to start the installation\\ \\ {{: | - Click **Next** to start the installation\\ \\ {{: | ||
| - | - Upon completion of the installation of the **CN-0188 Evaluation Software**, the installer for the **ADI SDP Drivers** will execute.\\ \\ <WRAP left tip round box 60%> | + | - Upon completion of the installation of the **CN-0218 Evaluation Software**, the installer for the **ADI SDP Drivers** will execute.\\ \\ <WRAP left tip round box 60%> |
| - Press **“Next”** to set the installation location for the **SDP Drivers**.\\ \\ <WRAP left round tip 50%>It is recommended that you install the drivers to the default directory path \\ **C: | - Press **“Next”** to set the installation location for the **SDP Drivers**.\\ \\ <WRAP left round tip 50%>It is recommended that you install the drivers to the default directory path \\ **C: | ||
| - Press **“Install”** to install the **SDP Drivers** and complete the installation of all software. | - Press **“Install”** to install the **SDP Drivers** and complete the installation of all software. | ||
| Line 67: | Line 67: | ||
| ---- | ---- | ||
| ===== Using the Evaluation Software ===== | ===== Using the Evaluation Software ===== | ||
| - | ====Test Setup Tab==== | + | ==== Main Window |
| - | {{ : | + | {{ : |
| - | | + | - **Connect** Button - Starts the connection between the [[ADI> |
| + | - **Reset and Disconnect** - Resets the board and ends the connection between the [[ADI> | ||
| + | - **Stop** Button - Stop collecting data from the CN0218 Board | ||
| + | - **Test Setup** Tab - Shows the acquired measurement data in terms of shunt voltage with respect to the samples\\ {{ : | ||
| + | * **Shunt Voltage** - Shunt voltage measurement output from ADC | ||
| + | * **Click to Start Sampling** - Starts acquisition of measurement data | ||
| + | * **Clear Data** - Clear all data collected from the chart history | ||
| + | * **Save Data to File** - Save measurement data to file | ||
| + | | ||
| + | * **Flash LED** - Flashes the LED on the SDP controller board | ||
| + | * **Read Firmware** - Reads the firmware of CN0218 Evaluation Board | ||
| + | - **Plot** Options - Edit plot display and options like interpolation and color of output waveform \\ {{ : | ||
| \\ | \\ | ||
| + | ==== Running the System ==== | ||
| + | -Open the CN0218.exe application from the default installation location | ||
| + | -Click the Connect Button | ||
| + | -Upon successful connection, start and control data acquisition through the data acquisition control buttons | ||
| + | -Output data will be shown in the graph. Edit graph through plot options and check boxes provided | ||
| + | -Click Disconnect if finished | ||
| + | -Click Quit to exit the program | ||
| ---- | ---- | ||
| Line 77: | Line 95: | ||
| * [[ftp:// | * [[ftp:// | ||
| * [[ADI> | * [[ADI> | ||
| - | * [[http:// | + | * [[adi>media/ |
| * [[ADI> | * [[ADI> | ||
| * [[ADI> | * [[ADI> | ||
| Line 87: | Line 105: | ||
| <WRAP round 80% download> | <WRAP round 80% download> | ||
| - | [[http:// | + | [[adi>media/ |
| * Schematics | * Schematics | ||
| * PCB Layout | * PCB Layout | ||
resources/eval/user-guides/circuits-from-the-lab/cn0218.txt · Last modified: 30 Jul 2021 07:22 by Victor Calinao, Jr