Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:eval:user-guides:circuits-from-the-lab:cn0196 [07 Dec 2017 08:04] – Glaizel Arinueloresources:eval:user-guides:circuits-from-the-lab:cn0196 [15 Dec 2017 22:57] – Brandon Bushey
Line 36: Line 36:
 ===== Connectors and Jumper Configurations ===== ===== Connectors and Jumper Configurations =====
  
-{{:resources:eval:user-guides:circuits-from-the-lab:hardware.png|}}+{{:resources:eval:user-guides:circuits-from-the-lab:new.png|}}
  
 ==== Description ==== ==== Description ====
-1. Switch S1: ON state provides an isolated side PWM pulses, OFF states makes the PWM disappears\\  +1. **Switch S1**: ON state provides an isolated side PWM pulses, OFF states makes the PWM disappears\\  
-2. Jumper Link LK1: Shorting pin 1 and 2 sets the Source Terminal of ADG787 to 5V while pin 2 and 3 sets to 0V.   \\  +2. **Jumper Link LK1**: Shorting pin 1 and 2 sets the Source Terminal of ADG787 to 5V while pin 2 and 3 sets to 0V.   \\  
-3. Header J1: Provides connection of the controlling signals between EVAL-CN0196-EB1Z and EVAL-ADuC7061MKZ as seen in below table+3. **Header J1**: Provides connection of the controlling signals between EVAL-CN0196-EB1Z and EVAL-ADuC7061MKZ as seen in below table
 ^EVAL-ADuC7061MKZ^EVAL-CN0196-EB1Z^ ^EVAL-ADuC7061MKZ^EVAL-CN0196-EB1Z^
 | PWRIN J1-1  | +5V_2  J1-1 | | PWRIN J1-1  | +5V_2  J1-1 |
Line 48: Line 48:
 | PWM0  J2-26 | PWM0_I J1-5 | | PWM0  J2-26 | PWM0_I J1-5 |
 | DVDD  J2-28 | +2V5   J1-3 | | DVDD  J2-28 | +2V5   J1-3 |
-4. Jumper Link LK2: Shorting pin 1 and 2 sets the Source Terminal of ADG787 to 5V while pin 2 and 3 sets to 0V. \\  +4. **Jumper Link LK2**: Shorting pin 1 and 2 sets the Source Terminal of ADG787 to 5V while pin 2 and 3 sets to 0V. \\  
-5. Jumper Link LK3: If pin 1 and 2 is shorted, disabling the ADUM7234 for under voltage condition is generated on board. Shorting pin 2 and 3 will provide externally disabling the isolator via J1-6 header. \\  +5. **Jumper Link LK3**: If pin 1 and 2 is shorted, disabling the ADUM7234 for under voltage condition is generated on board. Shorting pin 2 and 3 will provide externally disabling the isolator via J1-6 header. \\  
-6. Connector J3: See below table+6.** Connector J3**: See below table
 ^Pin Number^Description^ ^Pin Number^Description^
 | J3-1  | VDD: Power Supply of the load        | | J3-1  | VDD: Power Supply of the load        |
Line 59: Line 59:
 | J3-6  | GND: Ground connection               | | J3-6  | GND: Ground connection               |
  
-7. Connector J4: Connects +12V power supply and Ground return   \\  +7. **Connector J4**: Connects +12V power supply and Ground return   \\  
-8. Connector J2: Connection of an external supply up to +20V if jumper link LK4 is not shorted \\  +8. **Connector J2**: Connection of an external supply up to +20V if jumper link LK4 is not shorted \\  
-9. Jumper link LK4: Shorting this pin sets the VDD voltage to +12V +9. **Jumper link LK4**: Shorting this pin sets the VDD voltage to +12V 
  
 ===== Software and Driver Installation ===== ===== Software and Driver Installation =====
Line 95: Line 95:
   * **STOP APP**: Closing the CN0196 Evaluation Software   * **STOP APP**: Closing the CN0196 Evaluation Software
 2. Provides control to the following: 2. Provides control to the following:
-  * **PWM Pulse Width**: Sets the PWM pulse width up to 12.8ms <note>Pulse width should be less than half of the     Pulse Interval </note>+  * **PWM Pulse Width**: Sets the PWM pulse width up to 12.8ms  
 +<note>Pulse width should be less than half of the     Pulse Interval</note>
   * **PWM Interval**: Sets the PWM interval up to 12.8ms depending on the configured PWM pulse width   * **PWM Interval**: Sets the PWM interval up to 12.8ms depending on the configured PWM pulse width
   * **Start/Stop**: Provides continuous and discontinues pulses   * **Start/Stop**: Provides continuous and discontinues pulses
Line 118: Line 119:
 </WRAP> </WRAP>
  
 +// End of Document //
      
  
resources/eval/user-guides/circuits-from-the-lab/cn0196.txt · Last modified: 29 Sep 2021 05:23 by Trisha Cabildo

Page Tools