Both sides previous revisionPrevious revisionNext revision | Previous revision |
resources:eval:user-guides:adbt1000 [02 Nov 2021 12:47] – [Bill of Materials] Frances de la Rama | resources:eval:user-guides:adbt1000 [17 Nov 2021 01:38] (current) – Figure 5 Edit Frances de la Rama |
---|
- Connect the Device Under Test (electronic load or battery) to connector P5 on the switching power module. {{ :resources:eval:user-guides:adbt1000_two_wire_load_connection.jpg?300 |2-wire Battery Connection}} <WRAP centeralign> //Figure 3. 2-wire Battery Connection//</WRAP> | - Connect the Device Under Test (electronic load or battery) to connector P5 on the switching power module. {{ :resources:eval:user-guides:adbt1000_two_wire_load_connection.jpg?300 |2-wire Battery Connection}} <WRAP centeralign> //Figure 3. 2-wire Battery Connection//</WRAP> |
- Connect the SDP-S controller to the System Control Board. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 | SDP-S Connection}} <WRAP centeralign> //Figure 4. SDP-S Connection//</WRAP> | - Connect the SDP-S controller to the System Control Board. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 | SDP-S Connection}} <WRAP centeralign> //Figure 4. SDP-S Connection//</WRAP> |
- Connect power supplies of +/-15V to P5 of the system control board for the Auxiliary Power Input. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 |}} <WRAP centeralign> //Figure 5. Auxiliary Power Supply Connection//</WRAP> | - Connect power supplies of +/-15V to P5 of the system control board for the Auxiliary Power Input. {{ :resources:eval:user-guides:adbt1000_auxiliary_power_supply_connection.jpg?300 |}} <WRAP centeralign> //Figure 5. Auxiliary Power Supply Connection//</WRAP> |
- Connect power supplies for the DC bus voltage to P2 of the system control board. Connect an electronic load in parallel. Set the electronic load to CV mode at a level about 200mV above the DC bus voltage. {{ :resources:eval:user-guides:dc_bus_connection.jpg?300 | DC Bus Connection}} <WRAP centeralign> //Figure 6. DC Bus Connection//</WRAP> | - Connect power supplies for the DC bus voltage to P2 of the system control board. Connect an electronic load in parallel. Set the electronic load to CV mode at a level about 200mV above the DC bus voltage. {{ :resources:eval:user-guides:dc_bus_connection.jpg?300 | DC Bus Connection}} <WRAP centeralign> //Figure 6. DC Bus Connection//</WRAP> |
- Turn on Auxiliary power, then DC bus voltage, then electronic load at DC bus. | - Turn on Auxiliary power, then DC bus voltage, then electronic load at DC bus. |
{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_6_secondary.svg?600 |}} <WRAP centeralign> //Figure 72. System Control Board Layer 6 Secondary//</WRAP> \\ | {{ :resources:eval:user-guides:adbt1000_layout_scb_layer_6_secondary.svg?600 |}} <WRAP centeralign> //Figure 72. System Control Board Layer 6 Secondary//</WRAP> \\ |
| |
==== System Power Module ==== | ==== Switching Power Module ==== |
{{ :resources:eval:user-guides:adbt1000_schematic_system_power_module.svg?800 |}} <WRAP centeralign> //Figure 73. System Power Module//</WRAP> \\ | {{ :resources:eval:user-guides:adbt1000_schematic_system_power_module.svg?800 |}} <WRAP centeralign> //Figure 73. System Power Module//</WRAP> \\ |
{{ :resources:eval:user-guides:adbt1000_schematic_current_sense_and_socket_connections.svg?600 |}} <WRAP centeralign> //Figure 74. Current Sense and Socket Connection//</WRAP> \\ | {{ :resources:eval:user-guides:adbt1000_schematic_current_sense_and_socket_connections.svg?600 |}} <WRAP centeralign> //Figure 74. Current Sense and Socket Connection//</WRAP> \\ |
| |
===== Bill of Materials ===== | ===== Bill of Materials ===== |
<WRAP centeralign> **Table 3. System Control Board**</WRAP> | <WRAP centeralign> **Table 5. System Control Board**</WRAP> |
{{ :resources:eval:user-guides:adbt100_bom_scb2.1.svg?797 |}} | {{ :resources:eval:user-guides:adbt100_bom_scb2.1.svg?797 |}} |
{{ :resources:eval:user-guides:adbt1000_bom_scb3.svg?795 |}} | {{ :resources:eval:user-guides:adbt1000_bom_scb3.svg?795 |}} |
{{ :resources:eval:user-guides:adbt1000_bom_scb5.svg?800 |}} | {{ :resources:eval:user-guides:adbt1000_bom_scb5.svg?800 |}} |
{{ :resources:eval:user-guides:adbt1000_bom_scb6.svg?800 |}} | {{ :resources:eval:user-guides:adbt1000_bom_scb6.svg?800 |}} |
{{ :resources:eval:user-guides:adbt1000_bom_scb7.svg?800 |}} | {{ :resources:eval:user-guides:adbt1000_bom_scb7.svg?800 |}} \\ |
| \\ |
| |
| <WRAP centeralign> **Table 6. Switching Power Module**</WRAP> |
| {{ :resources:eval:user-guides:adbt1000_bom_spm1.1.svg?800 |}} |
| {{ :resources:eval:user-guides:adbt1000_bom_spm2.svg?800 |}} |
| {{ :resources:eval:user-guides:adbt1000_bom_spm3.svg?800 |}} \\ |
| |
| {{ :resources:eval:user-guides:adbt1000_copyright1.svg?800 |}} |
| |