Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:adbt1000 [02 Nov 2021 09:23] – [Registers Tab] Frances de la Ramaresources:eval:user-guides:adbt1000 [17 Nov 2021 01:38] (current) – Figure 5 Edit Frances de la Rama
Line 52: Line 52:
   - Connect the Device Under Test (electronic load or battery) to connector P5 on the switching power module. {{ :resources:eval:user-guides:adbt1000_two_wire_load_connection.jpg?300 |2-wire Battery Connection}} <WRAP centeralign> //Figure 3. 2-wire Battery Connection//</WRAP>   - Connect the Device Under Test (electronic load or battery) to connector P5 on the switching power module. {{ :resources:eval:user-guides:adbt1000_two_wire_load_connection.jpg?300 |2-wire Battery Connection}} <WRAP centeralign> //Figure 3. 2-wire Battery Connection//</WRAP>
   - Connect the SDP-S controller to the System Control Board. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 | SDP-S Connection}} <WRAP centeralign> //Figure 4. SDP-S Connection//</WRAP>   - Connect the SDP-S controller to the System Control Board. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 | SDP-S Connection}} <WRAP centeralign> //Figure 4. SDP-S Connection//</WRAP>
-  - Connect power supplies of +/-15V to P5 of the system control board for the Auxiliary Power Input. {{ :resources:eval:user-guides:adbt1000_sdp_s_connection.jpg?300 |}} <WRAP centeralign> //Figure 5. Auxiliary Power Supply Connection//</WRAP>+  - Connect power supplies of +/-15V to P5 of the system control board for the Auxiliary Power Input. {{ :resources:eval:user-guides:adbt1000_auxiliary_power_supply_connection.jpg?300 |}} <WRAP centeralign> //Figure 5. Auxiliary Power Supply Connection//</WRAP>
   - Connect power supplies for the DC bus voltage to P2 of the system control board. Connect an electronic load in parallel. Set the electronic load to CV mode at a level about 200mV above the DC bus voltage. {{ :resources:eval:user-guides:dc_bus_connection.jpg?300 | DC Bus Connection}} <WRAP centeralign> //Figure 6. DC Bus Connection//</WRAP>   - Connect power supplies for the DC bus voltage to P2 of the system control board. Connect an electronic load in parallel. Set the electronic load to CV mode at a level about 200mV above the DC bus voltage. {{ :resources:eval:user-guides:dc_bus_connection.jpg?300 | DC Bus Connection}} <WRAP centeralign> //Figure 6. DC Bus Connection//</WRAP>
   - Turn on Auxiliary power, then DC bus voltage, then electronic load at DC bus.    - Turn on Auxiliary power, then DC bus voltage, then electronic load at DC bus. 
Line 298: Line 298:
 ==== Help Tab ==== ==== Help Tab ====
 The Help tab provides the user with quick links to the user manual and quick start procedures for the system.  The Help tab provides the user with quick links to the user manual and quick start procedures for the system. 
-{{ :resources:eval:user-guides:adbt1000_gui_help_tab.jpg?800 |}} <WRAP centeralign> //Figure 57.  Help Tab//</WRAP> \\+{{ :resources:eval:user-guides:adbt1000_gui_help_tab.svg?800 |}} <WRAP centeralign> //Figure 57.  Help Tab//</WRAP> \\
  
 ===== Evaluation Board Schematics and Layout ===== ===== Evaluation Board Schematics and Layout =====
  
 ==== System Control Board ==== ==== System Control Board ====
-{{ :resources:eval:user-guides:adbt1000_schematic_adbt1000_connections.svg?800 |}} <WRAP centeralign> //Figure 58.  ADBT1000 Connections//</WRAP>+{{ :resources:eval:user-guides:adbt1000_schematic_adbt1000_connections.svg?800 |}} <WRAP centeralign> //Figure 58.  ADBT1000 Connections//</WRAP>\\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_on_board_battery_monitor.svg?450 |}} <WRAP centeralign> //Figure 59.  Onboard Battery Monitor//</WRAP>\\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_spi_connections.svg?800 |}} <WRAP centeralign> //Figure 60.  SPI Connections//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_dc_bus_monitor_connection.svg? 450 |}} <WRAP centeralign> //Figure 61.  DC Bus Monitor Connections//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_power_sections.svg?800 |}} <WRAP centeralign> //Figure 62.  Power Section//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_current_sense_filter.svg?800 |}} <WRAP centeralign> //Figure 63.  Current Sense Filter//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_voltage_sense_buffers.svg?800 |}} <WRAP centeralign> //Figure 64.  Voltage Sense Buffer//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_connections_for_spm_sockets.svg?800 |}} <WRAP centeralign> //Figure 65.  Connections for SPM Sockets//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_top_layer.svg?600 |}} <WRAP centeralign> //Figure 66.  System Control Board Top Layer//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_1_primary.svg?600 |}} <WRAP centeralign> //Figure 67.  System Control Board Layer 1 Primary//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_2_ground.svg?600 |}} <WRAP centeralign> //Figure 68.  System Control Board Layer 2 Ground//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_3_signal.svg?600 |}} <WRAP centeralign> //Figure 69.  System Control Board Layer 3 Signal//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_4_signal.svg?600 |}} <WRAP centeralign> //Figure 70.  System Control Board Layer 4 Signal//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_5_ground.svg?600 |}} <WRAP centeralign> //Figure 71.  System Control Board Layer 5 Ground//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_scb_layer_6_secondary.svg?600 |}} <WRAP centeralign> //Figure 72.  System Control Board Layer 6 Secondary//</WRAP> \\
  
 +==== Switching Power Module ====
 +{{ :resources:eval:user-guides:adbt1000_schematic_system_power_module.svg?800 |}} <WRAP centeralign> //Figure 73.  System Power Module//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_schematic_current_sense_and_socket_connections.svg?600 |}} <WRAP centeralign> //Figure 74.  Current Sense and Socket Connection//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_spm_silkscreen1.svg?600 |}} <WRAP centeralign> //Figure 75.  Switching Power Module Silkscreen//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_spm_primary_layer.svg?600 |}} <WRAP centeralign> //Figure 76.  Switching Power Module Primary Layer//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_spm_ground_layer.svg?600 |}} <WRAP centeralign> //Figure 77.  Switching Power Module Ground Layer//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_spm_power_layer.svg?600 |}} <WRAP centeralign> //Figure 78.  Switching Power Module Power Layer//</WRAP> \\ 
 +{{ :resources:eval:user-guides:adbt1000_layout_spm_secondary_layer.svg?600 |}} <WRAP centeralign> //Figure 79.  Switching Power Module Secondary Layer//</WRAP> \\ 
 +
 +===== Bill of Materials =====
 +<WRAP centeralign> **Table 5.  System Control Board**</WRAP>
 +{{ :resources:eval:user-guides:adbt100_bom_scb2.1.svg?797 |}} 
 +{{ :resources:eval:user-guides:adbt1000_bom_scb3.svg?795 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_scb4.svg?798 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_scb5.svg?800 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_scb6.svg?800 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_scb7.svg?800 |}} \\
 +\\
 +
 +<WRAP centeralign> **Table 6.  Switching Power Module**</WRAP>
 +{{ :resources:eval:user-guides:adbt1000_bom_spm1.1.svg?800 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_spm2.svg?800 |}}
 +{{ :resources:eval:user-guides:adbt1000_bom_spm3.svg?800 |}} \\
 +
 +{{ :resources:eval:user-guides:adbt1000_copyright1.svg?800 |}}
  
resources/eval/user-guides/adbt1000.1635841383.txt.gz · Last modified: 02 Nov 2021 09:23 by Frances de la Rama

Page Tools