| Both sides previous revisionPrevious revision | |
| resources:eval:user-guides:ad9081_fmca_ebz:quickstart [13 Dec 2021 10:59] – Laszlo Nagy | resources:eval:user-guides:ad9081_fmca_ebz:quickstart [31 Oct 2023 15:15] (current) – Restructure page iulia Moldovan |
|---|
| | [[xilinx>VCK190]] | √ | √ | | | [[xilinx>VCK190]] | √ | √ | |
| | [[intel>A10Soc]] | √ | √ | | | [[intel>A10Soc]] | √ | √ | |
| | |
| ==== Supported Environments ==== | ==== Supported Environments ==== |
| |
| | [[xilinx>VCU118]] | √ | √ | √ | | | [[xilinx>VCU118]] | √ | √ | √ | |
| |
| ==== HDL Reference Design ==== | ==== Quick Start Guides ==== |
| * [[resources:eval:user-guides:ad9081_fmca_ebz:ad9081_fmca_ebz_hdl|AD9081-FMCA-EBZ (Single MxFE) HDL Reference Design]] | |
| | |
| ==== Software support ==== | |
| | |
| * [[:resources:tools-software:linux-drivers:iio-mxfe:ad9081|AD9081 Linux Driver Support]] | |
| | |
| | |
| ==== Hardware Setup ==== | |
| | |
| In most carriers, the [[adi>AD9081-FMCA-EBZ | AD9081-FMCA-EBZ]] board connects to the HPC0 connector (unless otherwise noted). The carrier setup requires power, UART (115200), ethernet (Linux), DisplayPort or HDMI (if available) and/or JTAG (no-OS) connections. A few typical setups are shown below. | |
| | |
| | |
| {{page>:resources:eval:user-guides:ad9081_fmca_ebz:ad9081_fmca_ebz_hdl##board_setup&nofooter&noeditbtn}} | |
| |
| === ZC706 + AD9081-FMCA-EBZ === | === ZC706 + AD9081-FMCA-EBZ === |
| * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:zynq|Zynq-7000 SoC ZC706 Quick Start Guide]] | * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:zynq|Zynq-7000 SoC ZC706 Quick Start Guide]] |
| |
| {{ :resources:eval:user-guides:ad9081_fmca_ebz:quickstart:ad9081-fmca-ebz-zc706.png?600 |}} | |
| |
| === ZCU102 + AD9081-FMCA-EBZ === | === ZCU102 + AD9081-FMCA-EBZ === |
| * [[resources:eval:user-guides:ad9081_fmca_ebz:quickstart:zynqmp|AD9081 Zynq UltraScale+ MPSoC ZCU102 Quick Start Guide]] | * [[resources:eval:user-guides:ad9081_fmca_ebz:quickstart:zynqmp|AD9081 Zynq UltraScale+ MPSoC ZCU102 Quick Start Guide]] |
| |
| {{ :resources:eval:user-guides:ad9081_fmca_ebz:quickstart:hwsetup_zcu102_ad9081.jpg?600 |}} | |
| |
| |
| === VCU118 + AD9081-FMCA-EBZ === | === VCU118 + AD9081-FMCA-EBZ === |
| * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:microblaze|Virtex UltraScale+ VCU118 Quick Start Guide]] | * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:microblaze|Virtex UltraScale+ VCU118 Quick Start Guide]] |
| |
| {{ :resources:eval:user-guides:ad9081_fmca_ebz:quickstart:hwsetup_vcu118_ad9081.jpg?600 |}} | |
| |
| === VCK190/VMK180 + AD9081-FMCA-EBZ/AD9082-FMCA-EBZ === | === VCK190/VMK180 + AD9081-FMCA-EBZ/AD9082-FMCA-EBZ === |
| * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:versal|Versal ACAP VCK190/VMK180 Quick Start Guide]] | * [[:resources:eval:user-guides:ad9081_fmca_ebz:quickstart:versal|Versal ACAP VCK190/VMK180 Quick Start Guide]] |
| |
| {{ :resources:eval:user-guides:ad9081_fmca_ebz:quickstart:hwsetup_vck190_ad9081.jpg?600 |}} | === A10SoC + AD9081-FMCA-EBZ === |
| | * [[:resources:eval:user-guides:ad9081:quickstart:a10soc|Arria10 SoC Quick Start Guide]] |
| |
| | ==== Hardware Setup ==== |
| | |
| | In most carriers, the [[adi>AD9081-FMCA-EBZ | AD9081-FMCA-EBZ]] board connects to the HPC0 connector (unless otherwise noted). The carrier setup requires power, UART (115200), ethernet (Linux), DisplayPort or HDMI (if available) and/or JTAG (no-OS) connections. A few typical setups are shown below. |
| | |
| | |
| | {{page>:resources:eval:user-guides:ad9081_fmca_ebz:ad9081_fmca_ebz_hdl##board_setup&nofooter&noeditbtn}} |
| | |
| | ==== HDL Reference Design ==== |
| | * [[resources:eval:user-guides:ad9081_fmca_ebz:ad9081_fmca_ebz_hdl|AD9081-FMCA-EBZ (Single MxFE) HDL Reference Design]] |
| | |
| | ==== Software support ==== |
| | |
| | * [[:resources:tools-software:linux-drivers:iio-mxfe:ad9081|AD9081 Linux Driver Support]] |
| |
| ====== ====== | ====== ====== |
