Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:ad-fmcomms2-ebz:quickstart [28 May 2019 21:13] – Add networking info Travis Collinsresources:eval:user-guides:ad-fmcomms2-ebz:quickstart [02 Mar 2021 07:48] (current) – [SoCkit + ARRADIO] Stefan-Robert Raus
Line 18: Line 18:
 | [[xilinx>ZCU102]] |  √  |  √  |   | | [[xilinx>ZCU102]] |  √  |  √  |   |
 | [[http://zedboard.org/product/zedboard|Zed Board]] |     |  √  |   | | [[http://zedboard.org/product/zedboard|Zed Board]] |     |  √  |   |
-| [[http://zedboard.org/product/mini-itx| MITX045]] |     |  √  |   |+| [[http://zedboard.org/product/mini-itx-board| MITX045]] |     |  √  |   |
 | [[https://www.arrow.com/en/products/sockit/arrow-development-tools|SoCKit]] |  |  |  √  | | [[https://www.arrow.com/en/products/sockit/arrow-development-tools|SoCKit]] |  |  |  √  |
  
Line 34: Line 34:
 | [[xilinx>ZCU102]] |  √  |  √  |  √  |  | [[xilinx>ZCU102]] |  √  |  √  |  √  | 
 | [[http://zedboard.org/product/zedboard|Zed Board]] |  √  |  √  |   √  |  | [[http://zedboard.org/product/zedboard|Zed Board]] |  √  |  √  |   √  | 
-| [[http://zedboard.org/product/mini-itx|MITX045]] |  √  |  √  |   √  | +| [[http://zedboard.org/product/mini-itx-board|MITX045]] |  √  |  √  |   √  | 
  
  
Line 68: Line 68:
  
 ^ ^ MSEL0 ^ MSEL1 ^ MSEL2 ^ MSEL3 ^ MSEL4 ^ CODEC_SEL ^ ^ ^ MSEL0 ^ MSEL1 ^ MSEL2 ^ MSEL3 ^ MSEL4 ^ CODEC_SEL ^
-|**POS**|  0  |  0  |  1  |  0  |  0  |  0  |+|**POS**|  0  |  1  |  0  |  1  |  0  |  0  |
  
 {{:resources:eval:user-guides:ad-fmcomms2-ebz:sockit_sw6.jpg?200|}} {{:resources:eval:user-guides:ad-fmcomms2-ebz:sockit_sw6.jpg?200|}}
Line 90: Line 90:
 | Carrier        | 1  | | Carrier        | 1  |
  
 +For our standard evaluation system most users boot from the SD cards placed either on the SOM or carrier board. For the **ADRV1CRR-BOB** carrier or carriers without SD card slots be sure to set S1 to 0.
  
 ===== Networking ===== ===== Networking =====
  
 By default, all SD cards for the prototyping platform (not TES) are configured for DHCP networking over their Ethernet interfaces. If you want to change the networking interfaces to use static addresses, which is required for directly connected Ethernet cables without DHCP servers in the loop, a [[https://github.com/analogdevicesinc/linux_image_ADI-scripts/blob/master/enable_static_ip.sh|helper script]] is provided. By default, all SD cards for the prototyping platform (not TES) are configured for DHCP networking over their Ethernet interfaces. If you want to change the networking interfaces to use static addresses, which is required for directly connected Ethernet cables without DHCP servers in the loop, a [[https://github.com/analogdevicesinc/linux_image_ADI-scripts/blob/master/enable_static_ip.sh|helper script]] is provided.
 +
 +To update the IP address of the board you must be logged into the board over UART or JTAG or Ethernet.
  
 From the development board or SOM itself run the following with the desired IP address: From the development board or SOM itself run the following with the desired IP address:
resources/eval/user-guides/ad-fmcomms2-ebz/quickstart.1559070837.txt.gz · Last modified: 28 May 2019 21:13 by Travis Collins

Page Tools