Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:eval:user-guides:ad-fmcomms2-ebz:quickstart:zynq [04 Jun 2021 20:29] – [AD-FMCOMMS2/3/4/5-EBZ Zynq and ZED Quick Start Guide] Robin Getzresources:eval:user-guides:ad-fmcomms2-ebz:quickstart:zynq [09 Jun 2021 12:11] – Add details to link Iulia Moldovan
Line 19: Line 19:
 ===== Creating / Configuring the SD Card ===== ===== Creating / Configuring the SD Card =====
  
-[[resources/tools-software/linux-software/zynq_images|Create SD Image for Zynq/ZED Boards. (it is a single image for all boards)]]+Create the [[resources/tools-software/linux-software/zynq_images|SD Image]] for Zynq/ZED Boards. (it is a single image for all boards)
  
 {{page>wiki/common#esd_warning&nofooter&noheader}} {{page>wiki/common#esd_warning&nofooter&noheader}}
Line 29: Line 29:
   - Get the [[xilinx>ZC706]]   - Get the [[xilinx>ZC706]]
     - {{http://www.xilinx.com/images/product-images/zc706-base-board.jpg}}     - {{http://www.xilinx.com/images/product-images/zc706-base-board.jpg}}
-  - Build the HDL project and make the BOOT.BIN (see [[:resources:fpga:docs:build|this tutorial]]) +  - Prepare the SD card with the proper Linux image (from [[:resources:tools-software:linux-software:zynq_images|here]] and pay attention to the Linux/Windows setup).
-  - Build the devicetree (see [[:resources:tools-software:linux-build:generic:zynq|this tutorial]]) +
-  - Prepare the SD card with the proper Linux image (see [[:resources:tools-software:linux-software:zynq_images|here]] and pay attention to the Linux/Windows setup), BOOT.BIN, and devicetree (you get the last ones from the previous steps)+
   - Insert the SD-CARD into the SD Card Interface Connector (J30)   - Insert the SD-CARD into the SD Card Interface Connector (J30)
   - Plug the AD-FMCOMMS2-EBZ into the LPC LPC Connector (J5)   - Plug the AD-FMCOMMS2-EBZ into the LPC LPC Connector (J5)
Line 42: Line 40:
   - Wait another ~30 seconds for the HDMI display device to start showing signs of life.   - Wait another ~30 seconds for the HDMI display device to start showing signs of life.
   - The follow the instructions for the type of demo that you want to do.     - The follow the instructions for the type of demo that you want to do.  
 +
 ===== Booting the SD Card ===== ===== Booting the SD Card =====
  
Line 59: Line 58:
   - Set the Jumpers and Switches accordingly like shown on the picture. (click on the picture to enlarge)   - Set the Jumpers and Switches accordingly like shown on the picture. (click on the picture to enlarge)
     - {{:resources:eval:user-guides:ad-fmcomms2-ebz:quickstart:zed_sw.jpg?300|ZED Board prepared}}     - {{:resources:eval:user-guides:ad-fmcomms2-ebz:quickstart:zed_sw.jpg?300|ZED Board prepared}}
-  - Build the HDL project and make the BOOT.BIN (see [[:resources:fpga:docs:build|this tutorial]]) +  - Prepare the SD card with the proper Linux image (see [[:resources:tools-software:linux-software:zynq_images|here]] and pay attention to the Linux/Windows setup)
-  - Build the devicetree (see [[:resources:tools-software:linux-build:generic:zynq|this tutorial]]) +
-  - Prepare the SD card with the proper Linux image (see [[:resources:tools-software:linux-software:zynq_images|here]] and pay attention to the Linux/Windows setup), BOOT.BIN, and devicetree (you get the last ones from the previous steps)+
   - Insert the SD-CARD into the SD Card Interface Connector (J12)   - Insert the SD-CARD into the SD Card Interface Connector (J12)
   - Plug the AD-FMCOMMS2-EBZ or AD-FMCOMMS3-EBZ into the LPC Connector (J1)   - Plug the AD-FMCOMMS2-EBZ or AD-FMCOMMS3-EBZ into the LPC Connector (J1)
Line 75: Line 72:
   - Wait another ~30 seconds for the HDMI display device to start showing signs of life. (Linux TUX top left)   - Wait another ~30 seconds for the HDMI display device to start showing signs of life. (Linux TUX top left)
   - Follow the instructions for the type of demo that you want to do on screen.   - Follow the instructions for the type of demo that you want to do on screen.
 +
 +<note tip>
 +If you want to manually build the HDL project and make the BOOT.BIN, see [[:resources:fpga:docs:build|this tutorial]]. For the Zynq Linux kernel and the devicetree, check [[:resources:tools-software:linux-build:generic:zynq|this tutorial]].
 +</note>
  
 Setup/Wiring. (click to enlarge): Setup/Wiring. (click to enlarge):
Line 81: Line 82:
  
 **Note:** For proper robustness shield the ZED board with a plexi-glass cover. Add a "Touch-Screw" (A2, stainless steel) and connect it via a 270kOhm resistor to a GND pin. Touch this screw prior any handling of any board. It ensures proper and painless ESD discharge. **Note:** For proper robustness shield the ZED board with a plexi-glass cover. Add a "Touch-Screw" (A2, stainless steel) and connect it via a 270kOhm resistor to a GND pin. Touch this screw prior any handling of any board. It ensures proper and painless ESD discharge.
- 
-  
  
  
resources/eval/user-guides/ad-fmcomms2-ebz/quickstart/zynq.txt · Last modified: 08 Aug 2023 15:20 by Laurentiu Popa

Page Tools