Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
====== AD-FMCOMMS2-EBZ / AD-FMCOMMS4-EBZ / AD-FMCOMMS5-EBZ Specifications ======

|The following equipments were used to generate the following characterization data:|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:setup2.jpg?400|}}|
|The Agilent Technology MXA Signal Analyzer and the Rohde&Schwarz SMA 100A Signal Generator.|

These specs are common to any of the boards which use a narrow band balun.

===== Transmit Specs =====

==== LO BW ====

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:tx_lo_sweep.png?400|}}|
|LO linearity sweep with 1MHz tone, -10dB attenuation and scale of 0.25|




==== Intermodulation Distortion ====
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:imd3_tx_lo2.4ghz_1mhzspacing_-4dbattenuation_0.625scale.png?400|}}|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:imd3_tx_lo2.4ghz_1mhzspacing_-4dbattenuation_0.125scale.png?400|}}|
|Phase Noise at LO of 2.4GHz and Tone of 1MHz with eights power out.|Phase Noise at LO of 2.4GHz and Tone of 1MHz with quarter power out.|

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:imd3_tx_lo2.4ghz_1mhzspacing_-4dbattenuation_0.25scale.png?400|}}|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:imd3_tx_lo2.4ghz_1mhzspacing_-4dbattenuation_0.5scale_0000.png?400|}}|
|Phase Noise at LO of 2.4GHz and Tone of 1MHz with half power out.|Phase Noise at LO of 2.4GHz and Tone of 1MHz with full power out.|

==== Phase Noise ====

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:phase_noise_tx_lo2.4ghz_1mhztone_-10dbattenuation_0.5scale_.png?400|}}|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:phase_noise_tx_lo2.4ghz_1mhztone_-10dbattenuation_0.25scale.png?400|}}|
|1MHz tone, LO 2.4GHz, Scale of 0.5|1MHz tone, LO 2.4GHz, Scale of 0.25|



====  EVM ====

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_10tx_0dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE10, with 0dB attenuation and 2.4GHz LO|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_10tx_10dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE10, with -10dB attenuation and 2.4GHz LO|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_10tx_20dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE10, with -20dB attenuation and 2.4GHz LO|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_20tx_0dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE20, with 0dB attenuation and 2.4GHz LO|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_20tx_10dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE20, with -10dB attenuation and 2.4GHz LO|
|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_20tx_20dbatten_2_45ghz_fdd.png?500|}}|
|EVM test result using LTE20, with -20dB attenuation and 2.4GHz LO|

===== Receive Specs =====





==== LO BW ====

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:rx_lo_sweep.png?400|}}|
|RX linearity LO sweep with 1MHz tone, -10dB input power and 10dB hardware gain|
==== ====

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:lte_10_rx_slow_agc_2_45ghz_neg45dbm_input_tdd.png?500|}}|
|EVM using LTE10 with 2.4GHz LO and -45dBm input|


====  Bandwidth ====
[[wp>Bandwidth_(signal_processing)|Bandwidth]]

|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:bw_sweep_rx_lo2.4ghz_slowattack_gc.png?400|}}|{{:resources:eval:user-guides:ad-fmcomms2-ebz:hardware:bw_sweep_rx_lo2.4ghz_manual_gc.png?400|}}|
|BW with 2.4GHz LO and -10dBm input and Slow attack gain control|BW with 2.4GHz LO and -10dBm input and manual gain control|
Analog Devices Wiki

Page Tools
