Differences

This shows you the differences between two versions of the page.

--- resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:dyno [07 Feb 2014 13:48] – [User Guide] Andrei Cozma
+++ resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:dyno [10 Feb 2021 04:43] (current) – add retired Robin Getz
@@ Line 1: / Line 1: @@
-====== Dynamo-meter Drive System ======
+====== Dynamometer Drive System ======
+{{page>/wiki/common#retired&nofooter&noheader}}
-{{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:ad-dyno1-ebz.png?400|Dynamo-meter Drive System}}
+{{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:ad-dyno1-ebz.png?400|Dynamometer Drive System}}
 ===== Features =====
-  * Two BLDC motors connected in a dyno setup
+  *[[http://www.anaheimautomation.com/products/brushless/brushless-motor-item.php?sID=143&pt=i&tID=96&cID=22|Two BLDC motors connected in a dyno setup (BLY171S-24V-4000 and BLY171D-24V-4000)]]\\
   * Electronically adjustable load – the load value is set using the onboard buttons + LCD
   * Programmable step and ramp load changes
@@ Line 12: / Line 12: @@
 ===== Block Diagram =====
 {{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:dyno_diagram.png?800|}}
 |< 100% 100% >|
@@ Line 38: / Line 37: @@
 | :::                        | Step load menu. Select "Step" to start toggling the load.\\ \\ \\ |
 | :::                        | Press "+" or "-" to toggle between the preset step values.\\ In order to go back press "Enter"\\ \\ |
-| :::                        | Set maximim duty cycle.\\ In order to go back press "Enter" \\ \\ |
+| :::                        | Set maximum duty cycle.\\ In order to go back press "Enter" \\ \\ |
 | :::                        | Set minimum duty cycle.\\ In order to go back press "Enter" \\ \\ |
 | :::                        | Ramp load menu. Press "+" or "-" to change ramp period.\\ In order to go back press "Enter" \\ \\ |
@@ Line 47: / Line 46: @@
 |< 100% 100% >|
 ^  ^
+===== Analog Discovery™  =====
+In order interface the Dyno with the Analog Discovery™ USB Oscilloscope:
+  * Slide switch S2 to EXT_CTRL position
+  * Insert the Analog Discovery™ in P1 the connector(with the Analog Devices logo facing the user)
-<WRAP round alert>
+{{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:dyno_discovery_control.JPG?400|Dynamometer Drive System}}
+Two software packages are available for interfacing with Analog Discovery™:
+  *[[http://www.digilentinc.com/Products/Detail.cfm?NavPath=2,66,849&Prod=WAVEFORMS|Digilent® WaveForms™]]\\
+  *[[http://www.mathworks.co.uk/help/daq/examples/getting-started-acquiring-data-with-digilent-analog-discovery.html|MathWorks Analog Discovery toolbox ]]\\
+The signals available to the  Analog Discovery™ are:
+^ Dyno Signal ^ Analog Discovery channel ^ Description ^
+| I_A | Scope Channel 1 Positive | Phase A motor current (185mv/A) |
+| I_B | Scope Channel 2 Positive | Phase B motor current (185mv/A) |
+| PWM1 | Digital Channel 0 | Phase A PWM (3.3V levels) |
+| PWM2 | Digital Channel 2 | Phase B PWM (3.3V levels) |
+| PWM3 | Digital Channel 2 | Phase C PWM (3.3V levels) |
+|< 100% 100% >|
+^  ^
+<WRAP round alert 80%>
 The system needs a 5V 500mA power supply. The power connector is a 2.1 X 5.5MM jack with the center pin positive(+)
+</WRAP>
+===== Downloads =====
+<WRAP round download 85%>
+**AD-DYNO1-EBZ**
+  * {{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:ad-dyno1-ebz_schematics.pdf|Schematics}}
+  * {{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:ad-dyno1-ebz_bom.pdf|Bill of Materials}}
+  * {{:resources:eval:user-guides:ad-fmcmotcon1-ebz:hardware:ad-dyno1-ebz_layout.zip|Allegro Board File}} (This file is [[http://www.7-zip.org/7z.html|compressed]]). Get the [[https://www.cadence.com/en_US/home/tools/pcb-design-and-analysis/allegro-downloads-start.html|Allegro FREE Physical Viewer]] (You need 16.5 or higher).
 </WRAP>
 {{navigation AD-FMCMOTCON1-EBZ#signal_chain|Signal Measurement Chain#..:|Overview#none}}

Wiki

Analog Devices Wiki

Differences

Analog Devices Wiki

Differences

Page Tools