This version is outdated by a newer approved version.
This version (25 Feb 2014 10:31) was approved by Andrei Cozma.The Previously approved version (11 Feb 2014 17:18) is available.
This version (25 Feb 2014 10:31) was approved by Andrei Cozma.The Previously approved version (11 Feb 2014 17:18) is available.This is an old revision of the document!
Table of Contents
AD-FMCMOTCON1-EBZ Controller Board
Features and Block Diagram
- Compatible with all Xilinx FPGA platforms with FMC LPC or HPC connectors
- 2 x Gbit Ethernet PHYs for high speed industrial communication
- Hall + Differential Hall + Encoder + Resolver interfaces
- Current and voltage measurement using isolated ADCs
- Xilinx XADC interface
- Fully isolated control and feedback signals
| Simplified Block Diagram | Detailed Block Diagram |
|---|
Picture and Main Components
Key Parts
| Measurement | |
|---|---|
| AD7401A | 5 kV rms, isolated 2nd order Sigma-Delta modulator |
| ADA4084-2 | 30 V, Low noise, rail-to-rail I/O, low power operational amplifier |
| AD8646 | 24 MHz rail-to-rail dual op amp |
| AD2S1210 | Variable resolution, 10-bit to 16-bit R/D converter with reference oscillator |
| Power | |
| ADuM5000 | isoPower® integrated isolated dc-to-dc converter |
| ADP1614 | 1000 mA, 2.5 MHz buck-boost dc-to-dc converter |
| ADM660 | CMOS switched-capacitor voltage converter |
| Isolation | |
| ADuM7640 | Triple channel digital isolator |
| Voltage Translation | |
| ADG3308 | 8-channel bidirectional level translator |
| Multiplexers | |
| ADG704 | CMOS, low voltage 2.5 Ω 4-channel multiplexer |
| ADG759 | CMOS low voltage, 3 ohms 4-channel multiplexer |
| High Speed Communication | |
| 88E1512 | Marvell Integrated 10/100/1000 Mbps Energy Efficient Ethernet Transceiver |
Jumper settings
| Sensor Selection | ||
|---|---|---|
| Back EMF | P9 - position 0 | P20 - position 0 |
| Single ended Hall | P9 - position 1 | P20 - position 0 |
| Differential Hall | P9 - position 0 | P20 - position 1 |
| Reserved | P9 - position 1 | P20 - position 1 |
| Resolver Configuration Mode | ||
| Normal Mode - Position input | P3 - Not inserted | P5 - Not inserted |
| Normal Mode - Velocity input | P3 - Not inserted | P5 - Inserted |
| Reserved | P3 - Inserted | P5 - Not inserted |
| Configuration Mode | P3 - Inserted | P5 - Inserted |
| Resolver Resolution Settings | ||
| 10 Bits | P4 - Not inserted | P6 - Not inserted |
| 12 Bits | P4 - Not inserted | P6 - Inserted |
| 14 Bits | P4 - Inserted | P6 - Not inserted |
| 16 Bits | P4 - Inserted | P6 - Inserted |
| PHYs Configuration | ||
| 2.5V VDDO, different PHY addresses | P11 & P12 - Position 0 | P9 - Inserted |
LEDs
| LED | Description |
|---|---|
| DS1 | FMC 3.3V Power Good |
| DS2 | Vadj Power Good |
| DS3 | 5V Power Good |
| DS7 | 12V Power Good |
Power Map
ADC FPGA Interface
The AD7401 Isolated Sigma-Delta Modulators present on the controller board have a 2 wires signal interface with the FPGA:
- 10 / 20 MHz clock input
- 1 bit digital data stream output
The reconstruction of the data provided by the AD7401 modulator can be done using a SINC3 filter. A filter model and HDL implementation are provided in the AD7401 datasheet. Typical filter output characteristics:
- Output code: 16 bit
- Sampling rate: 78kHz
The output code resolution and sampling rate can be controlled by changing the filter’s model and decimation. Polyphase interpolation filters are utilized to increase the sampling rate of the system.
Position & Speed Sensors FPGA Interface
Single digital interface for multiple position sensors
- Single Ended HALL
- Differential HALL
- BEMF
- Encoder
3 digital signals between HW and the FPGA
- HALL A / BEMF A / Encoder Channel A
- HALL B / BEMF B / Encoder Channel B
- HALL C / BEMF C / Encoder Index
Sensor selection is done with jumpers on the controller board. The hardware conditions the analog signals and sends clean digital signals to the FPGA.
Downloads
AD-FMCMOTCON1-EBZ
- Allegro Board File (This file is compressed). Get the Allegro FREE Physical Viewer (You need 16.5 or higher).
Navigation - AD-FMCMOTCON1-EBZ
Up: OverviewNext.: Low Voltage Drive Board
resources/eval/user-guides/ad-fmcmotcon1-ebz/hardware/controller_board.1393320678.txt.gz · Last modified: 25 Feb 2014 10:31 by Andrei Cozma