Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
====== AD-FMCJESDADC1-EBZ Microblaze Quick Start Guide ======

<note warning>**NOTE:**\\
Support for the ad-fmcjesdadc1-ebz is discontinued on Microblaze carriers (kc705 and vc707) starting with 2022_R2 Kuiper Linux release and it wont be supported in future releases. 
Latest microblaze images with pre-build files can be downloaded from [[https://wiki.analog.com/resources/tools-software/linux-drivers/platforms/microblaze_loading|here]]. Check this [[:resources:tools-software:linux-software:adi-kuiper_images:release_notes|link]] to see all Kuiper releases.
</note>

This guide provides some quick instructions (still takes awhile to download, and set things up) on how to setup the AD-FMCJESDADC1-EBZ on:

  * [[xilinx>VC707]] 
  * [[xilinx>KC705]] 

===== Required Software =====
  * Bitfile and Linux ELF image.
  * Xilinx ISE Microprocessor Debugger (XMD) is sufficient for the demo.
  * A UART terminal (Tera Term/Hyperterminal), Baud rate 115200 (8N1).


===== Required Hardware =====
  * Xilinx VC707 or KC705
  * AD-FMCJESDADC1-EBZ FMC Board.
  * Micro / Mini-USB Cable

====== Testing ======

  * Connect the AD-FMCJESDADC1-EBZ FMC board to the FPGA carrier, on the KC705: FMC HPC or VC707: FMC1 HPC connector.
  * Connect USB JTAG (Micro USB) to your host PC. 
  * Turn on the power switch on the FPGA board.
  * Open XMD console to configure the FPGA and download the elf image.

===== Loading =====

{{page>resources:tools-software:linux-drivers:platforms:microblaze_loading#LOADING&noheader&firstseconly&noeditbtn}}



===== Messages =====

{{page>resources:tools-software:linux-drivers:platforms:microblaze_loading#MESSAGES&noheader&firstseconly&noeditbtn}}   

<WRAP box bggreen><wrap info>This specifies any shell prompt running on the target</wrap>
<xterm>
Early console on uartlite at 0x40600000
bootconsole [earlyser0] enabled
Ramdisk addr 0x00000000, 
Compiled-in FDT at 80323fe8
Linux version 3.17.0-126736-gdf1ca8f-dirty (michael@mhenneri-D04) (gcc version 4.8.3 20140131 (prerelease) (crosstool-NG 1.18.0) ) #1943 Wed Dec 17 11:03:18 CET 2014
setup_cpuinfo: initialising
setup_cpuinfo: Using full CPU PVR support
wt_msr_noirq
setup_memory: max_mapnr: 0x30000
setup_memory: min_low_pfn: 0x80000
setup_memory: max_low_pfn: 0xb0000
setup_memory: max_pfn: 0xb0000
Zone ranges:
  DMA      [mem 0x80000000-0xafffffff]
  Normal   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x80000000-0xbfffffff]
On node 0 totalpages: 196608
free_area_init_node: node 0, pgdat 8040751c, node_mem_map 81000000
  DMA zone: 1536 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 196608 pages, LIFO batch:31
early_printk_console remapping from 0x40600000 to 0xffffd000
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 195072
Kernel command line: console=ttyUL0,115200
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 768436K/786432K available (3215K kernel code, 148K rwdata, 724K rodata, 5988K init, 86K bss, 17996K reserved)
Kernel virtual memory layout:
  * 0xffffe000..0xfffff000  : fixmap
  * 0xffffd000..0xffffe000  : early ioremap
  * 0xb0000000..0xffffd000  : vmalloc & ioremap
NR_IRQS:128
/axi@0/axi-intc@41200000: num_irq=21, edge=0x3810
/axi@0/axi-timer@41c00000: irq=1
xilinx_timer_set_mode: shutdown
xilinx_timer_set_mode: periodic
sched_clock: 32 bits at 99MHz, resolution 10ns, wraps every 43383508981ns
Calibrating delay loop... 48.94 BogoMIPS (lpj=244736)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
devtmpfs: initialized
regulator-dummy: no parameters
NET: Registered protocol family 16
Switched to clocksource xilinx_clocksource
xilinx_timer_set_mode: oneshot
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
XGpio: /axi@0/gpio@40020000: registered, base is 243
XGpio: /axi@0/gpio@40020000: dual channel registered, base is 235
Skipping unavailable RESET gpio -2 (reset)
futex hash table entries: 256 (order: -1, 3072 bytes)
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 1500
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
40600000.serial: ttyUL0 at MMIO 0x40600000 (irq = 4, base_baud = 0) is a uartlite
console [ttyUL0] enabled
console [ttyUL0] enabled
bootconsole [earlyser0] disabled
bootconsole [earlyser0] disabled
brd: module loaded
Xilinx SystemACE device driver, major=254
xilinx_lcd 40010000.gpio_lcd: Device Tree Probing 'gpio_lcd'
xilinx_lcd 40010000.gpio_lcd: LCD 0x40010000 mapped to 0xb0140000
xilinx_spi 44a70000.axi-quad-spi: at 0x44A70000 mapped to 0xb0160000, irq=13
libphy: Fixed MDIO Bus: probed
xilinx_emaclite 40e00000.network: Device Tree Probing
libphy: Xilinx Emaclite MDIO: probed
xilinx_emaclite 40e00000.network: MAC address is now 00:0a:35:00:00:10
xilinx_emaclite 40e00000.network: Xilinx EmacLite at 0x40E00000 mapped to 0xB0034000, irq=2
i2c /dev entries driver
i2c i2c-0: Added multiplexed i2c bus 1
at24 2-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
at24 2-0054: 256 byte 24c02 EEPROM, writable, 1 bytes/write
i2c i2c-0: Added multiplexed i2c bus 2
i2c i2c-0: Added multiplexed i2c bus 3
i2c i2c-0: Added multiplexed i2c bus 4
i2c i2c-0: Added multiplexed i2c bus 5
i2c i2c-0: Added multiplexed i2c bus 6
i2c i2c-0: Added multiplexed i2c bus 7
i2c i2c-0: Added multiplexed i2c bus 8
pca954x 0-0074: registered 8 multiplexed busses for I2C switch pca9548
platform 44a10000.axi-ad9250-hpc-0: Driver cf_axi_adc requests probe deferral
platform 44a20000.axi-ad9250-hpc-1: Driver cf_axi_adc requests probe deferral
spi spi32765.2: Driver ad9467 requests probe deferral
spi spi32765.3: Driver ad9467 requests probe deferral
platform 44a91000.axi-jesd204b-rx: Driver cf_axi_jesd204b_v51 requests probe deferral
platform 44a60000.axi-jesd-gt-rx-tx: Driver cf_axi_jesd204b_gt requests probe deferral
ad9517 spi32765.1: probed
TCP: cubic registered
NET: Registered protocol family 17
platform 44a10000.axi-ad9250-hpc-0: Driver cf_axi_adc requests probe deferral
platform 44a20000.axi-ad9250-hpc-1: Driver cf_axi_adc requests probe deferral
spi spi32765.2: Driver ad9467 requests probe deferral
spi spi32765.3: Driver ad9467 requests probe deferral
platform 44a91000.axi-jesd204b-rx: Driver cf_axi_jesd204b_v51 requests probe deferral
cf_axi_jesd204b_gt 44a60000.axi-jesd-gt-rx-tx: AXI-JESD204B (6.00.b) at 0x44A60000 mapped to 0xb01a0000,
platform 44a10000.axi-ad9250-hpc-0: Driver cf_axi_adc requests probe deferral
platform 44a20000.axi-ad9250-hpc-1: Driver cf_axi_adc requests probe deferral
spi spi32765.2: Driver ad9467 requests probe deferral
spi spi32765.3: Driver ad9467 requests probe deferral
cf_axi_jesd204b_v51 44a91000.axi-jesd204b-rx: AXI-JESD204B 5.2 Rev 1, at 0x44A91000 mapped to 0xb0032000,
platform 44a10000.axi-ad9250-hpc-0: Driver cf_axi_adc requests probe deferral
platform 44a20000.axi-ad9250-hpc-1: Driver cf_axi_adc requests probe deferral
ad9467 spi32765.2: AD9250 PLL LOCKED, JESD204B Link Ready
ad9467 spi32765.3: AD9250 PLL LOCKED, JESD204B Link Ready
cf_axi_adc 44a10000.axi-ad9250-hpc-0: ADI AIM (8.00.b) at 0x44A10000 mapped to 0xb01e0000, probed ADC AD9250 as MASTER
cf_axi_adc 44a20000.axi-ad9250-hpc-1: ADI AIM (8.00.b) at 0x44A20000 mapped to 0xb0200000, probed ADC AD9250 as MASTER
Freeing unused kernel memory: 5988K (80409000 - 809e2000)
Starting logging: OK
Starting network...
Starting network...
udhcpc (v1.22.1) started
Sending discover...
xilinx_emaclite 40e00000.network eth0: Link is Down
Sending discover...
xilinx_emaclite 40e00000.network eth0: Link is Up - 100Mbps/Full - flow control off
Sending discover...
Sending select for 10.44.2.153...
Lease of 10.44.2.153 obtained, lease time 86400
deleting routers
adding dns 10.32.51.110
adding dns 10.64.53.110
random: ssh-keygen urandom read with 45 bits of entropy available
Starting sshd: OK
Starting IIO Server Daemon: OK


Welcome to Buildroot

buildroot login: 
</xterm></WRAP>

===== IIO Oscilloscope Remote  =====

Please see also here:[[resources:tools-software:linux-software:iio_oscilloscope|Oscilloscope]]

The IIO Oscilloscope application can be used to connect to another platform that has a connected device in order to configure the device and read data from it.

Build and start osc on a network enabled Linux host.

Once the application is launched goto Settings -> Connect and enter the IP address of the target in the popup window.
Analog Devices Wiki

Page Tools
