Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
====== AD-FMCDAQ2-EBZ/AD-FMCDAQ3-EBZ Microblaze Quick Start Guide ======

This guide provides some quick instructions (still takes awhile to download, and set things up) on how to setup the AD-FMCDAQ2-EBZ/AD-FMCDAQ3-EBZ on:
  * [[xilinx>KC705]]
  * [[xilinx>KCU105]]
  * [[xilinx>VC707]]

===== Required Software =====
  * Bitfile and Linux ELF image.
  * Xilinx ISE Microprocessor Debugger (XMD) is sufficient for the demo.
  * A UART terminal (Tera Term/Hyperterminal), Baud rate 115200 (8N1).

===== Required Hardware =====
  * Xilinx KC705 or KCU105 or VC707
  * AD-FMCDAQ2-EBZ/AD-FMCDAQ3-EBZ FMC Board.
  * Micro / Mini-USB Cable

====== Testing ======

  * Connect the AD-FMCDAQ2-EBZ/AD-FMCDAQ3-EBZ FMC board to the FPGA carrier, on the HPC FMC connector.
  * Connect USB JTAG (Micro USB) to your host PC. 
  * Turn on the power switch on the FPGA board.
  * Open XMD console to configure the FPGA and download the elf image.

===== Loading =====

{{page>resources:tools-software:linux-drivers:platforms:microblaze_loading#LOADING&noheader&firstseconly&noeditbtn}}



===== Messages =====

{{page>resources:tools-software:linux-drivers:platforms:microblaze_loading#MESSAGES&noheader&firstseconly&noeditbtn}}   

<WRAP box bggreen><wrap info>This specifies any shell prompt running on the target</wrap>
<xterm>
# Early console on uartlite at 0x40600000
bootconsole [earlyser0] enabled
Ramdisk addr 0x00000000, 
Compiled-in FDT at 8031cda8
Linux version 3.17.0-126658-g6807aea (michael@mhenneri-D04) (gcc version 4.8.3 20140131 (prerelease) (crosstool-NG 1.18.0) ) #1647 Fri Nov 21 10:33:05 CET 2014
setup_cpuinfo: initialising
setup_cpuinfo: Using full CPU PVR support
wt_msr_noirq
setup_memory: max_mapnr: 0x30000
setup_memory: min_low_pfn: 0x80000
setup_memory: max_low_pfn: 0xb0000
setup_memory: max_pfn: 0xb0000
Zone ranges:
  DMA      [mem 0x80000000-0xafffffff]
  Normal   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x80000000-0xbfffffff]
On node 0 totalpages: 196608
free_area_init_node: node 0, pgdat 803fb104, node_mem_map 80800000
  DMA zone: 1536 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 196608 pages, LIFO batch:31
early_printk_console remapping from 0x40600000 to 0xffffd000
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 195072
Kernel command line: console=ttyUL0,115200
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 771408K/786432K available (3187K kernel code, 143K rwdata, 708K rodata, 3061K init, 86K bss, 15024K reserved)
Kernel virtual memory layout:
  * 0xffffe000..0xfffff000  : fixmap
  * 0xffffd000..0xffffe000  : early ioremap
  * 0xb0000000..0xffffd000  : vmalloc & ioremap
NR_IRQS:128
/axi@0/axi-intc@41200000: num_irq=15, edge=0x3810
/axi@0/axi-timer@41c00000: irq=1
xilinx_timer_set_mode: shutdown
xilinx_timer_set_mode: periodic
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns
Calibrating delay loop... 48.51 BogoMIPS (lpj=97024)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
devtmpfs: initialized
NET: Registered protocol family 16
Switched to clocksource xilinx_clocksource
xilinx_timer_set_mode: oneshot
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
XGpio: /axi@0/gpio@40000000: registered, base is 251
XGpio: /axi@0/gpio@40000000: dual channel registered, base is 245
XGpio: /axi@0/gpio@40020000: registered, base is 232
XGpio: /axi@0/gpio@40020000: dual channel registered, base is 224
Skipping unavailable RESET gpio -2 (reset)
futex hash table entries: 256 (order: -1, 3072 bytes)
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 1506
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
40600000.serial: ttyUL0 at MMIO 0x40600000 (irq = 46, base_baud = 0) is a uartlite
console [ttyUL0] enabled
console [ttyUL0] enabled
bootconsole [earlyser0] disabled
bootconsole [earlyser0] disabled
of_serial 41400000.serial: Unknown serial port found, ignored
brd: module loaded
Xilinx SystemACE device driver, major=254
xilinx_lcd 40010000.gpio_lcd: Device Tree Probing 'gpio_lcd'
xilinx_lcd 40010000.gpio_lcd: LCD 0x40010000 mapped to 0xb01a0000
xilinx_spi 44a70000.axi-quad-spi: property name 'xlnx,num-ss-bits' is deprecated.
xilinx_spi 44a70000.axi-quad-spi: at 0x44A70000 mapped to 0xb01c0000, irq=10
libphy: Fixed MDIO Bus: probed
xilinx_axienet 40e00000.network: TX_CSUM 0
xilinx_axienet 40e00000.network: RX_CSUM 0
libphy: Xilinx Axi Ethernet MDIO: probed
i2c /dev entries driver
platform 44a10000.axi-ad9680-hpc: Driver cf_axi_adc requests probe deferral
spi spi32766.2: Driver ad9467 requests probe deferral
platform 44a90000.jesd204: Driver cf_axi_jesd204b_v51 requests probe deferral
platform 44a91000.jesd204: Driver cf_axi_jesd204b_v51 requests probe deferral
platform 44a60000.axi-jesd-gt: Driver cf_axi_jesd204b_gt requests probe deferral
ad9523 spi32766.0: probed ad9523-1
platform 44a04000.axi-ad9144-hpc: Driver cf_axi_dds requests probe deferral
ad9144 spi32766.1: Failed to get clocks
spi spi32766.1: Driver ad9144 requests probe deferral
TCP: cubic registered
NET: Registered protocol family 17
platform 44a10000.axi-ad9680-hpc: Driver cf_axi_adc requests probe deferral
spi spi32766.2: Driver ad9467 requests probe deferral
platform 44a90000.jesd204: Driver cf_axi_jesd204b_v51 requests probe deferral
platform 44a91000.jesd204: Driver cf_axi_jesd204b_v51 requests probe deferral
cf_axi_jesd204b_gt 44a60000.axi-jesd-gt: AXI-JESD204B (5.00.b) at 0x44A60000 mapped to 0xb0280000,
platform 44a04000.axi-ad9144-hpc: Driver cf_axi_dds requests probe deferral
ad9144 spi32766.1: Failed to get clocks
spi spi32766.1: Driver ad9144 requests probe deferral
platform 44a10000.axi-ad9680-hpc: Driver cf_axi_adc requests probe deferral
spi spi32766.2: Driver ad9467 requests probe deferral
cf_axi_jesd204b_v51 44a90000.jesd204: AXI-JESD204B 5.2 Rev 1, at 0x44A90000 mapped to 0xb0032000,
cf_axi_jesd204b_v51 44a91000.jesd204: AXI-JESD204B 5.2 Rev 1, at 0x44A91000 mapped to 0xb0034000,
platform 44a04000.axi-ad9144-hpc: Driver cf_axi_dds requests probe deferral
platform 44a10000.axi-ad9680-hpc: Driver cf_axi_adc requests probe deferral
ad9467 spi32766.2: AD9680 PLL LOCKED
cf_axi_dds 44a04000.axi-ad9144-hpc: Analog Devices CF_AXI_DDS_DDS MASTER (8.00.b) at 0x44A04000 mapped to 0xb0098000, probed DDS AD9144
cf_axi_adc 44a10000.axi-ad9680-hpc: ADI AIM (8.00.b) at 0x44A10000 mapped to 0xb02c0000, probed ADC AD9680 as MASTER
Freeing unused kernel memory: 3060K (803fc000 - 806f9000)
Starting logging: OK
Starting network...
Starting network...
udhcpc (v1.22.1) started
net eth0: Promiscuous mode disabled.
net eth0: Promiscuous mode disabled.
Sending discover...
xilinx_axienet 40e00000.network eth0: Link is Down
xilinx_axienet 40e00000.network eth0: Link is Up - 100Mbps/Full - flow control off
Sending discover...
Sending select for 10.44.2.94...
Lease of 10.44.2.94 obtained, lease time 86400
deleting routers
adding dns 10.32.51.110
adding dns 10.64.53.110
Starting dropbear sshd: OK
random: dropbear urandom read with 86 bits of entropy available
Starting IIO Server Daemon

Welcome to Buildroot
buildroot login: root
#
</xterm></WRAP>

===== IIO Oscilloscope Remote  =====

Please see also here:[[resources:tools-software:linux-software:iio_oscilloscope|Oscilloscope]]

The IIO Oscilloscope application can be used to connect to another platform that has a connected device in order to configure the device and read data from it.

Build and start osc on a network enabled Linux host.

Once the application is launched goto Settings -> Connect and enter the IP address of the target in the popup window.

{{ :resources:eval:user-guides:ad-fmcdaq2-ebz:quickstart:connect.png?300 | Connect Window}}

{{ :resources:eval:user-guides:ad-fmcdaq2-ebz:quickstart:plot_window.png?800 | Plot}}

{{ :resources:eval:user-guides:ad-fmcdaq2-ebz:quickstart:daq2_plugin.png?800 | DAQ2 plugin}}
Analog Devices Wiki

Page Tools
