Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:eval:dpg:ad974x-dpg2-ebz [27 Apr 2018 17:58] – [DPGDOWNLOADER SOFTWARE] Annette Hurmanresources:eval:dpg:ad974x-dpg2-ebz [07 Apr 2021 11:22] – Added Quick Start Guide Shine Cabatan
Line 1: Line 1:
-====== AD9743/5/6/7 Evaluation Board Quick Start Guide ====== +======EVALUATING THE AD9743/AD9745/AD9746/AD9747 DIGITAL-TO-ANALOG CONVERTER====== 
-===== WHAT’S IN THE BOX ===== +=====Preface===== 
-  * WHAT’S IN THE BOX +This user guide describes both the hardware and software setup needed to acquire data capture from [[adi>AD9743-DPG2-EBZ]]/[[adi>AD9745-DPG2-EBZ]]/[[adi>AD9746-DPG2-EBZ]]/[[adi>AD9747-DPG2-EBZ]] evaluation board to characterize [[adi>AD9743]]/[[adi>AD9745]]/[[adi>AD9746]]/[[adi>AD9747]] 10-/12-/14-/16-bit 250Msps high-speed digital-to-analog converter.
-  * AD9747-EBZ Evaluation Board +
-  * Mini-USB Cable +
-  * AD9747 Evaluation Board CD +
-EXAMPLE EQUIPMENT LIST +
-  * +5Vdc Power Supply: Agilent E3630A +
-  * Digital Pattern Generator( DPG2 or DPG3) OR System Demonstration Platform( SDP-H1) and FMC to High-Speed DAC Evaluation Board Adaptor(AD-DAC-FMC-ADP)   +
-  * DAC Clock Source: R&S SML 02 +
-  * AQM LO Clock Source: R&S SMA100A +
-  * Spectrum Analyzer: Agilent PSAA or R&S FSU +
-  * PC: Windows PC with 2 or more USB ports (See Appendix for system requirements) +
-===== INTRODUCTION ===== +
-The AD9747 Evaluation Board connects to the Analog Devices Digital Pattern Generator (DPG2, PN: ADI HSC-DAC-DPG-BZ; or DPG3, PN: AD –DPG3) or System Demonstration Platform (SDP-H1, PN: EVAL-SDP-CH1Z) to allow for quick evaluation of the AD9747. The DPG2 or SDP-H1 allows the user to create many types of digital vectors and transmit these at speed to the AD9747 in any of the AD9747 operating modes. The AD9747 evaluation board is configured over USB from a panel within the DPGDownloader software. +
-(Note: The AD9747 operation is described in detail. The operation of the other devices in the family is described in a later section.) +
-===== SOFTWARE INSTALLATION ===== +
-The AD9747 application software, DPGDownloader, should be installed on the PC prior connecting the hardware to the PC. The DAC Software Suite is included on the Evaluation Board CD, or can be downloaded from the DPG web site at http://www.analog.com/dpg. +
-This will install DPGDownloader required for loading vectors into the DPG2 and configuring the AD9747 evaluation board. +
-===== HARDWARE SETUP (DAC OUTPUT) ===== +
-Once the DPGDownloader software is installed, the hardware can be connected . A single 5V power supply powers the evaluation board. The power supply should be able to source up to 1A to cover all the board’s operating conditions. A low jitter clock source (< 0.5psec RMS) should be used for the DACCLK. A sinusoidal clock output level of 0 to 4dBm is optimal. By default, the DAC outputs are connected to SMA connectors for evaluation. Both DAC outputs are available. Later in the document, the modifications for observing the modulator output and different clocking options will be shown. +
-  * The evaluation board plugs directly into the DPG2 or DPG3. +
-The PC connects to both the DPG2 and the evaluation board through USB cables as shown in Figure 1 and Figure 2  +
-  * The evaluation board plugs into the AD-DAC-FMC-ADP adapter board that plugs into the SDP-H1. +
-The PC connects to both the SDP-H1 and the evaluation board through USB cables as shown in Figure 3 and Figure 4.+
  
-(Note: The AD-DAC-FMC-ADP adapter board allows AD974x-DPG2-EBZ DAC Evaluation Boards to be used on SDP-H1 with a FMC connector.)  +This guide shows how AD974x-DPG2-EBZ works with SDP-H1 controller board developed by Analog Devices. Link to the old user guide document is provided for customers who still have DPG2 and DPG3 controller boards. 
-{{ :resources:eval:dpg:dpg2-ad9747-1.png?300 |}} + 
-Figure 1. DPG2 and AD9747 Evaluation Board Bench set-up +=====Typical Setup===== 
-{{ :resources:eval:dpg:dpg2-ad9747-2.png?300 |}} +<WRAP centeralign>{{ :resources:eval:dpg:ad9747_sdp-h1_hardware_set-up.jpg?600 |}} 
-Figure 2. DPG2 and AD9747 Evaluation Board  +//Figure 1. EVAL-AD9743/45/46/47 Evaluation Setup//</WRAP> 
-{{ :resources:eval:dpg:sdph1-ad9747-1.png?300 |}} + 
-Figure 3. SDP-H1 and AD9747 Evaluation Board Bench set-up +<note tip>Tip: Click on any picture in this guide to open an enlarged version.</note> 
-{{ :resources:eval:dpg:sdph1-ad9747-2.png?300 |}} + 
-Figure 4. SDP-H1 and AD9747 Evaluation Board  +=====Helpful Files:===== 
-=====  BASIC HARDWARE SETUP ===== +  * Old version of [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747 Evaluation Board Quick Start Guide.pdf|User Guide]] as reference on evaluation board jumper selection 
-It is suggested that the basic set-up is verified before making any modifications to the evaluation board. +  * [[adi>static/imported-files/data_sheets/AD9743_9745_9746_9747.pdf|AD9743_45_46_47 Data Sheet]]  
-Connect the equipment to the AD9747 evaluation board per the following table: +  * IBIS Models: [[adi>/Analog_Root/static/techSupport/designTools/ibisModels/license/ibis_general.html?ibs=AD9747.ibs|AD9747]],[[adi>/Analog_Root/static/techSupport/designTools/ibisModels/license/ibis_general.html?ibs=AD9746.ibs|AD9746]],[[adi>/Analog_Root/static/techSupport/designTools/ibisModels/license/ibis_general.html?ibs=AD9745.ibs|AD9745]],[[adi>/Analog_Root/static/techSupport/designTools/ibisModels/license/ibis_general.html?ibs=AD9743.ibs|AD9743]] 
-  * Equipment         Connects to AD9747 Eval Board +  * [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747-DPG2-EBZ RevB Schematic.pdf|Schematic]] 
-  * Power Supply P5(+5V), P6(GND) +  * [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747-DPG2-EBZ RevB BOM_customer.xls|Bill of Materials]] 
-  * Signal Source J1(CLOCK IN), Set source to 100MHz, 2dBm output +  * [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747-DPG2-EBZ RevB Gerber Files.zip|PCB Gerber files]] 
-  * PC USB Cable XP2 +  * [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747-DPG2-EBZ RevB.brd|PCB BRD file]] 
-  * Spectrum Analyzer J5(IOUT1_P) or J9 (IOUT2_P) +  * [[ftp://ftp.analog.com/pub/HSSP_SW/HSCDAC/Documents/AD9747/AD9747-DPG2-EBZ RevB Layout.pdf|PCB Layout PDF]] 
-  * DPG2         P1 and P2 + 
-  * SDP-H1         J4(FMC connector) +<note tip>Tip: Open this page in Internet Explorer to avoid problems when downloading files.</note> 
-===== DPGDOWNLOADER SOFTWARE ===== + 
-Power up the DPG and connect the USB cable to the PC. Next, run the DPGDownloader Software. A shortcut will be installed to your Start menu during the installation of the DAC Software Suite. To begin, click on the DPGDownloader shortcut in your Programs menu, typically at Start > Programs > Analog Devices > DPG > DPGDownloader. +=====Software Needed:===== 
-The basic parts of the DPGDownloader window are; Hardware Config Panel, EVB Config, Vector Generation Pull-Down Menu, Vector Palette, Vector Selection Panel and the Download and Play buttons. +  * [[:resources:tools-software:ace|Analysis | Control | Evaluation (ACE) Software]] 
-{{ :resources:eval:dpg:ad9747-5.png |}} +  * [[:resources:tools-software:ace:dpg-lite|DPG Lite]] or [[:resources:eval:dpg:dpgdownloader|DPG Downloader]] 
-Figure 5. DPGDownloader Window + 
-  * - If the AD9747 evaluation board has been recognized by the PC, “AD9747 RevB” should be populated in the Evaluation Board field in the Hardware Config panel. +=====Hardware Needed:===== 
-  * - Generate a sinewave by pulling down the “Add Generated Waveform” menu and choosing “Single Tone”. Fill in the form as shown in Figure 5 (Sample Rate = 100MHz, Desired Frequency = 17.0MHz, etc.). Select the I and Q data vectors in the data selection panel. +  * [[adi>AD9743-DPG2-EBZ]]/[[adi>AD9745-DPG2-EBZ]]/[[adi>AD9746-DPG2-EBZ]]/[[adi>AD9747-DPG2-EBZ]] Evaluation Board 
-  * - Configure the eval board by writing the value 01 to register 1E1. This configures the AD9516 to use the CLK input to drive the clock path. +  * [[:resources:eval:dpg:hsdac-sdp-h1|SDP-H1]] (EVAL-SDP-CH1Z) Board 
-{{ :resources:eval:dpg:ad9747-6.png |}} +  * 12V 1A Wall Adapter for SDP-H1 
-  * - Bypass the clock dividers on the AD9516. +  * [[adi>AD-DAC-FMC]]-ADP High-Speed DAC Evaluation Board to FMC Adaptor Board 
-{{ :resources:eval:dpg:ad9747-7.png |}} +  * PC with ACE and DPG Lite Software Applications 
-  * - The DCO frequency field in the DPGDownloader window should now be reading something close to 100MHz. +  * 5V 1A Power Supply 
-  * - Next hit the download button. This transfers the data from the PC to the DPG memory. +  * High-Frequency Continuous Wave Generator 
-  * - When the vector has finished downloading, hit the play button. This starts the DPG2 transmitting data to the eval board. +  * Signal/Spectrum Analyzer 
-  * - The output from J5 and J9 should be a clean 29MHz tone as shown below: +  * (2) USB A to USB Mini Cables 
-{{ :resources:eval:dpg:ad9747-8.png |}} +  * (2) SMA Cables 
-===== Using the AD9743/AD9745/AD9746/AD9747 Evaluation Boards ===== +  * (2) Banana Plug Cables 
-The evaluation boards for the AD9743/AD9745/AD9746/AD9747 are identical except for the DUT installed. The operation of the eval boards is also the same except for the vector generation “DAC Resolution” field and the Data Width fields as shown below. + 
-These fields should be configured to match the DUT. +=====Quick Start Guide===== 
-{{ :resources:eval:dpg:ad9747-9.png |}} +  - Attach AD9743-DPG2-EBZ/AD9745-DPG2-EBZ/AD9746-DPG2-EBZ/AD9747-DPG2-EBZ to SDP-H1 FMC connector using the AD-DAC-FMC-ADP adapter board. Connect continuous wave generator for clock input to J1 and DAC output from J8 to a signal/spectrum analyzer. Connect the evaluation board to PC via USB and to a 5V 1A power supply via banana plug cables. Refer to Figure 1. 
-===== Selecting the Modulator Outputs ===== +  - Connect SDP-H1 to PC via USB and to a 12V 1A power supply. 
-By default, solder jumpers JP4, JP5, JP6, and JP7 configure the DAC outputs to be observed at SMA outputs J5 and J9. This jumper setting is shown in Figure 6 a). To connect the DAC outputs to the LPF and the ADL537x analog quadrature modulator, the solder jumpers need to be repositioned as shown in Figure 6 b). The modulator output can be observed thru the SMA connector J6 (MODULATED OUTPUT). The modulator LO input can be sourced thru SMA connector J10 (LOCAL OSC INPUT). The clock level into the modulator should be set to about 3dBm. +  - Set clock input to 100MHz and 2dBm. 
-{{ :resources:eval:dpg:ad9747-10.png |}} +  - Open ACE. The board will be automatically recognized by the software. Otherwise, install the plugin for AD9747. 
-===== Eval Board Jumper Options ===== +  - Start DPG Lite or DPG Downloader. At the SDP-H1 part of the software, the device part number and clock frequency should be displayed. 
-There are 6 pin jumpers on the evaluation board corresponding to the 6 supplies on the board. They serve as ‘switches’ that determine if the LDOs on board or external supplies are used for each individual supply. They are shunted by default, which means on board LDOs  are used. When an external supply is necessary, pull off the shunt from the corresponding supply and connect the external supply to the SMA test points close to the jumper. +  - In ACE, apply the default values in the Initial Configuration wizard as shown in Figure 2.{{ :resources:eval:dpg:ad9747_ace_boardview.png?600 |}}<WRAP centeralign> 
-{{ :resources:eval:dpg:ad9747-11.png |}}+//Figure 2. ACE Initial Configuration Wizard for EVAL-AD9747//</WRAP> 
 +  - In DPG Lite or DPG Downloader, from the Add Generator Waveforms pulldown menu select Single Tone and apply the settings as shown in Figure 3. Set the desired frequency to 17 MHz. Set DAC resolution to the DAC’s number of bits (16 for AD9747, 14 for AD9746, and so on). Check the Generate Complex Data (I & Q) box.{{ :resources:eval:dpg:ad9747_dpg-lite_sdp-h1.png?600 |}}<WRAP centeralign> 
 +//Figure 3. DPG Lite session for EVAL-AD9747//</WRAP> 
 +  - Select the in-phase tone from the I Data Vector pulldown menu and the quadrature tone from the Q Date Vector pulldown menu. 
 +  - Press the download arrow and then the play button. The spectrum similar to Figure 4 should appear in the signal/spectrum analyzer.{{ :resources:eval:dpg:ad9747_output_sdp-h1_.png?600 |}}<WRAP centeralign> 
 +//Figure 4. EVAL-AD9747 FFT for Fdac=100MHz, Fout=17MHz//</WRAP>
  
resources/eval/dpg/ad974x-dpg2-ebz.txt · Last modified: 07 Jun 2023 02:20 by James Peevee Salenga

Page Tools