Differences

This shows you the differences between two versions of the page.

--- resources:eval:ads8-v1 [16 Nov 2017 21:12] – created Tony Meyers
+++ resources:eval:ads8-v1 [03 Jan 2021 22:12] (current) – fix links Robin Getz
@@ Line 1: / Line 1: @@
-Placeholder for ADS8-V1EBZ
+====== ADS8-V1EBZ HIGH SPEED EVALUATION BOARD ======
+===== Preface =====
+The [[adi>en/content/CU_High-Speed_ADC_FIFO_evaluation_tools/fca.html#ADS8-V1|ADS8-V1]] Evaluation Board was developed to support the evaluation of Analog Devices High Speed Data Converters with JESD204B bit rates up to 16Gbps.  This Wiki site provides a high level overview of the platform. In addition, each use-case of the board has its own section (e.g. Using the ADS8-V1 for High Speed A/D Converter Evaluation).  The ADS8-V1 is intended to be used only with specified Analog Devices Evaluation Boards.  The ADS8-V1 is not intended to be used as a general purpose development platform, and no support is available for standalone operation. The ADS8-V1 may contain hardware features not fully productized or supported by our default customer evaluation configurations. Please refer to Xilinx and its approved distributors for general purpose FPGA Development Kits.
+===== ADS8-V1EBZ Features =====
+.	Xilinx Kintex Ultrascale XCKU040-3FFVA1156E FPGA.
+.	One (1) FMC+ connector.
+.	Twenty (20) 16Gbps transceivers supported by one (1) FMC+ connector.
+.	DDR4 SDRAM.
+.	Simple USB 3.0 port interface.
+{{ :resources:eval:ads8-v1ebztop.jpg?nolink&600 |}}
+<WRAP centeralign>
+//Figure 1. ADS8-V1EBZ High Speed Evaluation Board (Top)//
+</WRAP>
+{{ :resources:eval:ads8-v1ebzbottom.jpg?nolink&600 |}}
+<WRAP centeralign>
+//Figure 2. ADS8-V1EBZ High Speed Evaluation Board (Bottom)//
+</WRAP>
+\\
+\\
+\\
+\\
+====== Using the ADS8-V1EBZ to evaluate High Speed A/D Converters ======
+===== Overview =====
+When connected to a specified Analog Devices high speed adc evaluation board, the ADS8-V1 works as a data acquistion board. Designed to support the highest speed JESD204B A/D Converters, the FPGA on the ADS8-V1 acts as the data receiver, while the ADC is the data transmitter. A typical test setup is shown below.
+\\
+{{ :resources:eval:ADS8-V1EBZ-AD9208 Typ Setup.png?nolink&600 |}}
+<WRAP centeralign>
+//Figure 3. ADS8-V1 connected to High Speed A/D Converter Evaluation Board//
+</WRAP>
+\\
+\\
+===== Helpful Documents =====
+  * [[adi>an-905|AN-905 Application Note]], //VisualAnalog Converter Evaluation Tool Version 1.0 User Manual//
+  * [[adi>an-878|AN-878 Application Note]], //High Speed ADC SPI Control Software//
+  * [[adi>an-877|AN-877 Application Note]], //Interfacing to High Speed ADCs via SPI//
+  * [[adi>an-835|AN-835 Application Note]], //Understanding ADC Testing and Evaluation//
+  * {{ :resources:eval:ads8-v1_triggered_capture.pdf |}}, //ADS8-V1 Triggered Capture//
+===== Software Download Links =====
+  * High Speed ADC SPI Control Software, [[adi>en/design-center/advanced-selection-and-design-tools/interactive-design-tools/spicontroller.html]]
+  * High Speed ADC VisualAnalog Software, [[adi>en/design-center/advanced-selection-and-design-tools/interactive-design-tools/visualanalog.html]]
+  * Analysis | Control | Evaluation (ACE) Software, [[adi>en/design-center/evaluation-hardware-and-software/ace-software.html]]
+===== Design and Integration Files =====
+  * Schematic, BOM, & Cadence BRD File Archive,  {{:resources:eval:20_041151d.zip|}}
+The ADC data sheets and User Guides provide additional product specific information and should be consulted when using the evaluation board. All documents and software tools are available at  [[adi>hsadcevalboard|High Speed ADC Eval Boards]]. For additional information or questions, send an email to highspeed.converters@analog.com.
+\\
+===== ADS8-V1EBZ Supported ADC Evaluation Boards =====
+Refer to the Analog Devices High Speed ADC capture board product page at [[adi>hsadcevalboard|High Speed ADC Eval Boards]] for a table of ADS8-V1EBZ compatible ADC evaluation boards.\\

Analog Devices Wiki

Differences

Page Tools