Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:eval:ad9083 [18 Jan 2021 14:52] – [Set Up MicroZed™ Connection] Alex Arrantsresources:eval:ad9083 [22 Feb 2021 22:16] – [Evaluation] Alex Arrants
Line 158: Line 158:
 {{:resources:eval:ad9083:wide_BW_mode.PNG?600|Figure 6. AD9083EBZ Wide Bandwidth Real Output Mode Typical FFT}} {{:resources:eval:ad9083:wide_BW_mode.PNG?600|Figure 6. AD9083EBZ Wide Bandwidth Real Output Mode Typical FFT}}
  
-//Figure 7. AD9083EBZ Typical FFT //+//Figure 7. AD9083EBZ Wide Bandwidth Real Output Mode Typical FFT //
  
 **Narrow Bandwidth Complex Output Mode** **Narrow Bandwidth Complex Output Mode**
Line 187: Line 187:
 {{:resources:eval:ad9083:narrow_BW_mode.PNG?600|Figure 6. AD9083EBZ Narrow Bandwidth Complex Output Mode Typical FFT}} {{:resources:eval:ad9083:narrow_BW_mode.PNG?600|Figure 6. AD9083EBZ Narrow Bandwidth Complex Output Mode Typical FFT}}
  
-//Figure 8. AD9083EBZ Typical FFT //+//Figure 8. AD9083EBZ Narrow Bandwidth Complex Output Mode Typical FFT //
  
 +**Precision Time Domain Mode**
  
 +Parameters:
 +  * Sample rate = 1 GSPS.
 +  * On-chip PLL reference = 125 MHz.(Provided by the on-board AD9528)
 +  * VMAX = 1.8 V.
 +  * RTERM = 100 Ω.
 +  * fC = 800 MHz.
 +  * High Performance Mode = False
 +  * Fin Max = 50 MHz (sample rate/20).
 +  * Backoff = 0
 +  * # ADC Channels = 16
 +  * Bypass CIC = False
 +  * CIC decimator = 8.
 +  * Use Mixer? = False
 +  * Decimate by J = Bypass (Decimate by 1)
 +  * jtx_subclasv_cfg = 0
 +  * Lanes (L) = 3
 +  * Virtual Converters (M) = 16
 +  * (Octets/Frame)/Lane(F) = 8
 +  * Bits Packed (NP) = 12
 +  * Resolution Bits (N) = 12
 +  * Frames in a multi-frame (K) = 32
 +  * 3 lanes at 10 Gbps each.
 +
 +  -Configure the AD9083 and AD9528 using the AD9083EBZSTARTUP WIZARD using the parameters listed above.
 +  -Click "Apply". It will take several moments for the configuration to complete.
 +  -Navigate to Analysis
 +  -Click "Run Once"
 +
 +You should see an FFT after setting up the board as shown and running the macro. 
 +{{:resources:eval:ad9083:ad9083_PTD.PNG?600|Figure 6. AD9083EBZ Narrow Bandwidth Complex Output Mode Typical FFT}}
 +
 +//Figure 9. AD9083EBZ Precision Time Domain Mode Typical FFT //
 ===== Troubleshooting Notes ===== ===== Troubleshooting Notes =====
 **Evaluation Board is not Functioning Properly** **Evaluation Board is not Functioning Properly**
resources/eval/ad9083.txt · Last modified: 05 Jan 2022 16:45 by Brigid Duggan

Page Tools