Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
Next revisionBoth sides next revision
eval:hmc8362_user_guide [10 Aug 2020 15:05] – created Kieran Barretteval:hmc8362_user_guide [10 Aug 2020 15:24] – [GETTING STARTED] Kieran Barrett
Line 19: Line 19:
  
 ====ONLINE RESOURCES==== ====ONLINE RESOURCES====
-HMC8362 data sheet +  * HMC8362 data sheet 
-HMC8364 data sheet +  * HMC8364 data sheet 
-Linduino DC2026C Demo Manual +  * Linduino DC2026C Demo Manual 
  
 ====GENERAL DESCRIPTION==== ====GENERAL DESCRIPTION====
Line 28: Line 28:
  
 ====EV1HMC8362LP6G/EV1HMC8364LP6G EVALUATION BOARD PHOTOGRAPH==== ====EV1HMC8362LP6G/EV1HMC8364LP6G EVALUATION BOARD PHOTOGRAPH====
- +{{ :eval:figure_1_evb_pic.png?600 |}} 
-**Insert Photo***+Figure 1. Evaluation Board
  
 ====GETTING STARTED==== ====GETTING STARTED====
 ===EVALUATION BOARD SETUP PROCEDURE=== ===EVALUATION BOARD SETUP PROCEDURE===
 To configure the EV1HMC8362LP6G or EV1HMC8364LP6G for the first time, perform the following steps.  To configure the EV1HMC8362LP6G or EV1HMC8364LP6G for the first time, perform the following steps. 
-1. Verify that the analog power supply that is used to power the evaluation board configured to allow an output of 6.0 V and 200 mA of compliance current.  +  - Verify that the analog power supply that is used to power the evaluation board configured to allow an output of 6.0 V and 200 mA of compliance current.  
-2. Disable the power supply output.  +  - Disable the power supply output.  
-3. Using a double shielded BNC cable and a BNC to SMA adapter, connect the analog power supply to J1.  +  - Using a double shielded BNC cable and a BNC to SMA adapter, connect the analog power supply to J1.  
-4. Use the supplied shorting jumpers to configure the logic, as shown in Figure 2. In the configuration shown in Figure 2, the ADG1604 multiplexer, VCO 1 of the HMC8362 or HMC8364,, and the output buffer amplifier are all enabled. When a jumper is disconnected the corresponding signal is pulled up to VCC. To reset a pin, connect the shorting jumper from the pin to the adjacent ground (GND). Figure 2 is annotated in green to indicate where a jumper is connected, and hence shorted to ground. +  - Use the supplied shorting jumpers to configure the logic, as shown in Figure 2. In the configuration shown in Figure 2, the ADG1604 multiplexer, VCO 1 of the HMC8362 or HMC8364,, and the output buffer amplifier are all enabled. When a jumper is disconnected the corresponding signal is pulled up to VCC. To reset a pin, connect the shorting jumper from the pin to the adjacent ground (GND). Figure 2 is annotated in green to indicate where a jumper is connected, and is therefore shorted to ground. 
-5. Connect the low noise, variable power supply to the SMA connector on the tuning port (J2) using a double shielded BNC cable and a BNC to SMA adapter. Torque this connection to 8 in/lb using an SMA torque wrench.   +  - Connect the low noise, variable power supply to the SMA connector on the tuning port (J2) using a double shielded BNC cable and a BNC to SMA adapter. Torque this connection to 8 in/lb using an SMA torque wrench.   
-6. Connect a 50 Ω RF cable capable of mating to the 2.92 mm K connector at J3 and torque this connection to 8 in/lb. Connect the other end of the cable to a signal source analyzer.   +  - Connect a 50 Ω RF cable capable of mating to the 2.92 mm K connector at J3 and torque this connection to 8 in/lb. Connect the other end of the cable to a signal source analyzer.   
-7. Enable the 6 V power supply. Approximately 103 mA is drawn if the part is configured correctly. +  - Enable the 6 V power supply. Approximately 103 mA is drawn if the part is configured correctly. 
-8. Enable the variable power supply and adjust the tuning voltage to within the range of the VCO band being used.  +  - Enable the variable power supply and adjust the tuning voltage to within the range of the VCO band being used.  
-9. Verify that the correct output frequency is observed on the signal source analyzer. An example using the HMC8362 is outlined in the Evaluation and Test section. +  - Verify that the correct output frequency is observed on the signal source analyzer. An example using the HMC8362 is outlined in the Evaluation and Test section. 
- +{{ :eval:figure_2_p1_connector.png?200 |}} 
-***Insert Figure***+Figure 2 Connector P1 Jumper Configuration: Alternative 5 V Supply,   Multiplexer, One VCO, and Buffer Amplifier Enabled
  
 ====EVALUATION BOARD HARDWARE==== ====EVALUATION BOARD HARDWARE====
eval/hmc8362_user_guide.txt · Last modified: 10 Aug 2020 19:39 by Kieran Barrett

Page Tools