Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
university:courses:electronics:electronics-lab-10 [24 Jul 2017 15:25] – change amplitude value to peak-peak Antoniu Miclausuniversity:courses:electronics:electronics-lab-10 [05 Nov 2021 15:29] (current) – [Activity: Shunt regulator] Doug Mercer
Line 1: Line 1:
-====== Activity 10. Shunt regulator ======+======Activity: Shunt regulator - ADALM2000======
  
 ===== Objective: ===== ===== Objective: =====
Line 25: Line 25:
 ===== Hardware Setup: ===== ===== Hardware Setup: =====
  
-Waveform generator W1 should be configured for a 1 KHz triangle wave with 4 volt amplitude and 2V offset. The Single ended input of scope channel 2 (2+) is used to measure the regulated output voltage at the collector of Q<sub>3</sub>.+{{:university:courses:electronics:bandgap_sh_reg-bb.png|}} 
 + 
 +<WRAP centeralign> Figure 2 Band-gap shunt regulator Breadboard Circuit </WRAP> 
 + 
 +Waveform generator W1 should be configured for a 1 KHz triangle wave with 4 volt amplitude peak-to-peak and 2V offset. The Single ended input of scope channel 2 (2+) is used to measure the regulated output voltage at the collector of Q<sub>3</sub>.
  
 ===== Procedure: ===== ===== Procedure: =====
  
 The regulated output voltage should be observed as the variable resistor R<sub>3</sub> is adjusted. The regulated output voltage should be observed as the variable resistor R<sub>3</sub> is adjusted.
 +
 +<WRAP centeralign>{{:university:courses:electronics:bandgap_sh_reg-wav.png?500|}}</WRAP>
 +
 +<WRAP centeralign> Figure 3 output voltage vs. input voltage  </WRAP>
  
 {{ :university:courses:electronics:a10_f2.png?500 |}} {{ :university:courses:electronics:a10_f2.png?500 |}}
  
-<WRAP centeralign> Figure 2 output voltage vs. input current </WRAP>+<WRAP centeralign> Figure 4 output voltage vs. input current </WRAP>
  
 =====Questions: ===== =====Questions: =====
Line 48: Line 56:
  
 All the emitters can be tired to ground ( pins 3,7,10,13 ). Devices Q<sub>1</sub>, Q<sub>2</sub> and Q<sub>3</sub> can be connected in parallel and serve as Q<sub>2</sub> in figure 1. Q<sub>4</sub> and Q<sub>5</sub> can be used for Q<sub>1</sub> and Q<sub>3</sub> in figure 2. The 3 to 1 emitter area ratio will result in an output voltage very nearly 1.2 volts if R<sub>1</sub> and R<sub>3</sub> are both equal to 2KΩ. All the emitters can be tired to ground ( pins 3,7,10,13 ). Devices Q<sub>1</sub>, Q<sub>2</sub> and Q<sub>3</sub> can be connected in parallel and serve as Q<sub>2</sub> in figure 1. Q<sub>4</sub> and Q<sub>5</sub> can be used for Q<sub>1</sub> and Q<sub>3</sub> in figure 2. The 3 to 1 emitter area ratio will result in an output voltage very nearly 1.2 volts if R<sub>1</sub> and R<sub>3</sub> are both equal to 2KΩ.
 +
 +<WRAP round download>
 +**Resources:**
 +  * Fritzing files: [[downgit>education_tools/tree/master/m2k/fritzing/shunt_volt_reg_bb | shunt_reg_bb]]
 +  * LTSpice files: [[downgit>education_tools/tree/master/m2k/ltspice/shunt_reg_ltspice | shunt_reg_ltspice]]
 +</WRAP>
  
 **Return to Lab Activity [[university:courses:electronics:labs|Table of Contents]]** **Return to Lab Activity [[university:courses:electronics:labs|Table of Contents]]**
  
university/courses/electronics/electronics-lab-10.1500902720.txt.gz · Last modified: 24 Jul 2017 15:25 by Antoniu Miclaus

Page Tools