Wiki

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
university:courses:electronics:comms-lab-colpitts-osc [04 Jun 2015 04:07]
dmercer [Directions:]
university:courses:electronics:comms-lab-colpitts-osc [27 Mar 2019 12:07]
amiclaus [Questions:] add ltspice files
Line 28: Line 28:
  
 =====Materials:​===== =====Materials:​=====
- +ADALM2000 Active Learning Module\\
-Analog Discovery Lab hardware\\+
 Solder-less breadboard, and jumper wire kit\\ Solder-less breadboard, and jumper wire kit\\
 1 - 2N3904 NPN transistor\\ 1 - 2N3904 NPN transistor\\
Line 50: Line 49:
 =====Hardware Setup:===== =====Hardware Setup:=====
  
-The green squares indicate where to connect the Discovery module ​AWG, scope channels and power supplies. Be sure to only turn on the power supplies after you double check your wiring.+<WRAP centeralign>​{{ :​university:​courses:​electronics:​colpitts_osc-bb.png|}}</​WRAP>​ 
 + 
 +<WRAP centeralign>​ Figure 3 Colpitts Oscillator breadboard circuit</​WRAP>​ 
 + 
 +The green squares indicate where to connect the ADALM2000module ​AWG, scope channels and power supplies. Be sure to only turn on the power supplies after you double check your wiring.
  
 =====Procedure:​===== =====Procedure:​=====
  
 Having finished construction the Colpitts oscillator check that the circuit is oscillating correctly by turning on both the + and - 5 V power supplies and connecting one of the oscilloscope channels to the output terminal. It may be found that the value of R<​sub>​3</​sub>​ is fairly critical, producing either a large distorted waveform or an intermittent low or no output. To find the best value for R<​sub>​3</​sub>,​ it could be replaced by a 1 KΩ or 5 KΩ potentiometer for experimentation to find the value that gives the best wave shape and reliable amplitude. The optimal value for R<​sub>​3</​sub>​ may change depending on the resonate frequency. Having finished construction the Colpitts oscillator check that the circuit is oscillating correctly by turning on both the + and - 5 V power supplies and connecting one of the oscilloscope channels to the output terminal. It may be found that the value of R<​sub>​3</​sub>​ is fairly critical, producing either a large distorted waveform or an intermittent low or no output. To find the best value for R<​sub>​3</​sub>,​ it could be replaced by a 1 KΩ or 5 KΩ potentiometer for experimentation to find the value that gives the best wave shape and reliable amplitude. The optimal value for R<​sub>​3</​sub>​ may change depending on the resonate frequency.
 +
 +A plot example using R<​sub>​1</​sub>​=10KΩ,​ R<​sub>​2</​sub>​=1KΩ,​ C<​sub>​1</​sub>​=4.7nF,​ C<​sub>​2</​sub>​=1nF is presented in Figure 4.
 +
 +<WRAP centeralign>​{{ :​university:​courses:​electronics:​colpitts_osc-wav.png|}}</​WRAP>​
 +
 +<WRAP centeralign>​ Figure 4 Colpitts Oscillator breadboard plot</​WRAP>​
  
 =====Questions:​===== =====Questions:​=====
Line 69: Line 78:
 |50 uH|  |  | |50 uH|  |  |
 |100 uH|  |  | |100 uH|  |  |
 +
 +<WRAP round download>​
 +**Lab Resources:​**
 +  * Fritzing files: [[ https://​minhaskamal.github.io/​DownGit/#/​home?​url=https://​github.com/​analogdevicesinc/​education_tools/​tree/​master/​m2k/​fritzing/​colpitts_osc_bb | colpitts_osc_bb]]
 +  * LTspice files: [[ https://​minhaskamal.github.io/​DownGit/#/​home?​url=https://​github.com/​analogdevicesinc/​education_tools/​tree/​master/​m2k/​ltspice/​colpitts_osc_ltspice | colpitts_osc_ltspice]]
 +</​WRAP>​
  
 **For Further Reading:** **For Further Reading:**
university/courses/electronics/comms-lab-colpitts-osc.txt · Last modified: 27 Mar 2019 12:07 by amiclaus