no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
| Previous revisionNext revision | |||
| — | resources:tools-software:sigmastudiov2:modules:gpioconditioning:updowncontrollut [10 May 2021 16:31] – Prasad Kamath | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | [[resources/ | ||
| + | ====== Up Down Control LUT ====== | ||
| + | {{: | ||
| + | \\ | ||
| + | ===== Description ===== | ||
| + | \\ | ||
| + | This block takes in two inputs, one up and one down, and uses them to generate an index for a lookup table. The starting index is pre-loaded into an interface register and the up/down inputs increment or decrement the value. | ||
| + | \\ | ||
| + | ===== Usage ===== | ||
| + | \\ | ||
| + | - Drag the block into your schematic. | ||
| + | - Connect the red control inputs to GPIOs that have been conditioned by Push and Hold, or to the outputs of the Rotary Encoder. | ||
| + | - Connect the yellow input pin to an Interface Read block. | ||
| + | - Connect the yellow output to an Interface Write block, with the same register selected for both the interface read and write blocks. | ||
| + | - The output will be the value in the table corresponding to the index. | ||
| + | \\ | ||
| + | ===== Targets Supported ===== | ||
| + | ^Name^ADSP-214xx^ADSP-215xx/ | ||
| + | |----------------------------------------|------------------------------------------|--------------------------------------------------|-------------------------------------------| | ||
| + | |Up Down Control LUT| Not supported | Not supported | Sample| | ||
| + | \\ | ||
| + | ===== Pins ===== | ||
| + | ==== Input==== | ||
| + | ^Name^Type^Description^ | ||
| + | |----------------------------------|-------------------|------------------------------------------------------------| | ||
| + | |Input0|Control|increment input (up)| | ||
| + | |Input1|Control|decrement input (down)| | ||
| + | |Input2|Logic|Connected to a software interface register - reads the last stored value at startup| | ||
| + | |||
| + | ==== Output==== | ||
| + | ^Name^Type^Description^ | ||
| + | |-----------------------------------|-------------------|----------------------------------------------------------------------------------------| | ||
| + | |Output0|Control| Output signal| | ||
| + | |Output1|Logic|Connected to a software interface register - writes the last output value| | ||
| + | |||
| + | \\ | ||
| + | ===== Configurable Parameters ===== | ||
| + | ^GUI Parameter Name^Default Value^Range^Function Description^ | ||
| + | | ---------------------------------------- | ---------------------- | ---------------------- | --------------------------------------------------------------------------------------------------------- | | ||
| + | |ByPassEnable| disable | enable/ | ||
| + | |NoOfTableValues|33 pts|[2, 800]|Sets the table size: the number of points used in the volume table curve.| | ||
| + | |TableValues|1|[-16, | ||
| + | |||
| + | \\ | ||
| + | ===== DSP Parameters ===== | ||
| + | ^Parameter Name^Description^ADAU145x/ | ||
| + | |--------------------------|---------------------------------------------------------------------------------------------------------------------------------- |---------------------------------| | ||
| + | |maxindex|maxnumber of table points|Fixed Point 32.0| | ||
| + | |table_p0|All the points in the table are written to the DSP in their linear gain format|Fixed Point 8.24| | ||
| + | |||
| + | \\ | ||
| + | ===== DSP Parameter Computation ===== | ||
| + | \\ | ||
| + | Not applicable | ||
| + | \\ | ||
resources/tools-software/sigmastudiov2/modules/gpioconditioning/updowncontrollut.txt · Last modified: 12 May 2021 14:28 by Prasad Kamath