Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
resources:tools-software:linuxdsp:docs:quickstartguide:quickstart_sc594 [28 Sep 2022 10:21] – Removed SHARC-ALSA example instructions Henrik Mauresources:tools-software:linuxdsp:docs:quickstartguide:quickstart_sc594 [24 Nov 2022 14:32] – Vasileios Bimpikas
Line 1: Line 1:
-===== Yocto Linux Quickstart Guide for ADSP-SC594 =====+===== Yocto Linux 2.1.0 Quickstart Guide for ADSP-SC594 =====
  
-<note important>The following instructions are for the ADSP-SC594-EZKIT development board (the EV-SC594-SOM System-on-Module (SOM) board attached to the EV-SOMCRR-EZKIT carrier board). For instructions for other processors and development boards please refer to [[resources:tools-software:linuxdsp:docs|Linux for ADSP-SC5xx: Documentation]]</note>+<note important>The following instructions are for the ADSP-SC594-EZKIT development board (the EV-SC594-SOM System-on-Module (SOM) board attached to the EV-SOMCRR-EZKIT carrier board). For instructions for other processors and development boards please refer to [[resources:tools-software:linuxdsp:releaselandingpages:2.1.0|Linux for ADSP-SC5xx Processors 2.1.0]]</note>
  
 ===== Setting Up Your Host PC ===== ===== Setting Up Your Host PC =====
Line 199: Line 199:
   : <code>   : <code>
 $ cd /tftpboot $ cd /tftpboot
-$ /opt/analog/cces/2.11.0/ARM/aarch64-none-elf/bin/aarch64-none-elf-gdb u-boot-proper-sc594-som-ezkit.elf +$ /opt/analog/cces/2.11.0/ARM/arm-none-eabi/bin/arm-none-eabi-gdb u-boot-proper-sc594-som-ezkit.elf 
 ... ...
 (gdb) target extended-remote :3333 (gdb) target extended-remote :3333
 Remote debugging using :3333 Remote debugging using :3333
 0x000000000000352c in ?? () 0x000000000000352c in ?? ()
-(gdb) load u-boot-spl-sc594-som-ezkit.elf 
-Loading section .text, size 0x13618 lma 0x20080000 
-Start address 0x20080000, load size 79384 
-Transfer rate: 34 KB/sec, 15876 bytes/write. 
-(gdb) c 
-Continuing. 
-^C 
-Program received signal SIGINT, Interrupt. 
-0x0000000020080ca0 in ?? () 
-</code> 
- 
-At this point you should see the following message in the first terminal. 
- 
-  ;''**Terminal1: minicom**'' 
-  : 
-<code> 
-U-Boot SPL 2020.10 (Aug 23 2022 - 13:09:23 +0000) 
-ADI Boot Mode: 0 (JTAG/BOOTROM) 
-SPL execution has completed.  Please load U-Boot Proper via JTAG 
-</code> 
- 
-Back in the third terminal, load U-Boot Proper into RAM. 
- 
-  ;''**Terminal3: GDB**'' 
-  : 
-<code> 
 (gdb) load (gdb) load
 Loading section .text, size 0x150 lma 0x96000000 Loading section .text, size 0x150 lma 0x96000000
resources/tools-software/linuxdsp/docs/quickstartguide/quickstart_sc594.txt · Last modified: 14 Sep 2023 10:11 by Vasileios Bimpikas

Page Tools