The most recent version of this page is a draft.
This version is outdated by a newer approved version.This version (10 Nov 2021 16:22) was approved by Henrik Mau.
This version is outdated by a newer approved version.This version (10 Nov 2021 16:22) was approved by Henrik Mau.This is an old revision of the document!
Table of Contents
Building The SDK
In order to build the SDK it is necessary to follow the instructions on Yocto Linux Quickstart Guide for ADSP-SC594 for Setting Up Your Host PC.
Preparing the buildtool
Yocto requires the environment to be configured before building is possible. A setup-environment script in the gxp folder contains all the required environment settings.
$ source setup-environment -m adsp-sc594-som-ezkit
Sourcing the script will configure your build environment and create a build folder along with a local build configuration file. See the Yocto Manual for further details.
Note that the build environment needs to be sourced once only before building. If later working in a different terminal the setup-environment script should be sourced again. If sourcing the setup-environment script is done without specifying the machine Yocto will reuse the previous configuration settings and retain any changes made to the files in the conf folder.
Building the SDK
To build the SDK for the adsp-sc5xx-minimal image invoke bitbake from within the build directory created previously.
$ bitbake adsp-sc5xx-minimal -c populate_sdk
When the build has completed you will find a set of files in the <BUILD_DIR>/tmp/deploy/sdk directory
$ ls tmp/deploy/sdk poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.host.manifest poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.sh poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.target.manifest poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.testdata.json
The poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.sh is a self-extracting archive containing the SDK.
Installing the SDK
Invoke the self-extracting archive. It will default to installing to /opt/poky/3.1.8 but gives you the option to select your own install folder during the installation.
$ ./poky-glibc-x86_64-adsp-sc5xx-minimal-armv7at2hf-neon-adsp-sc594-som-ezkit-toolchain-3.1.8.sh Poky (Yocto Project Reference Distro) SDK installer version 3.1.8 ================================================================= Enter target directory for SDK (default: /opt/poky/3.1.8): You are about to install the SDK to "/opt/poky/3.1.8". Proceed [Y/n]? y Extracting SDK...................................................................done Setting it up...done SDK has been successfully set up and is ready to be used. Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g. $ . /opt/poky/3.1.8/environment-setup-armv7at2hf-neon-poky-linux-gnueabi
Your SDK is now installed.
resources/tools-software/linuxdsp/docs/quickstartguide/building-the-sdk.1636380801.txt.gz · Last modified: 08 Nov 2021 15:13 by Sammy Arschavir