Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий
This version is outdated by a newer approved version.DiffThis version (27 Jul 2020 06:52) was approved by sullivan liu.

This is an old revision of the document!

Table of Contents

USB Gadget Zero

This page provides how to use the USB Gadget Zero on ADSP-SC5XX board, and it will include the below test:

  • USB gadget zero bulk
  • USB Gadget zero control
  • USB Gadget zero test

Hardware Configuration

Connect the USB micro-B plug cable into the USB HS/OTG Device port, as showing below:

Software Configuration

On the Yocto, Configure the linux-kernel as below to set the USB controller in Gadget only mode, and enable the USB Gadget zero relevant options. 

$ bitbake linux-adi -c menuconfig

Configure the USB drivers to Gadget only mode (or Dual role mode ) 

Device Drivers  --->
	[*] USB support  --->
                <*>   Inventra Highspeed Dual Role Controller
                        MUSB Mode Selection (Gadget only mode)  --->
                        *** Platform Glue Layer *** 
                <*>     ADI
                        *** MUSB DMA mode ***
                [N]     Disable DMA (always use PIO)  
                [*]       Inventra
                <*>   USB Gadget Support  --->

Configure the Gadget zero support 

Device Drivers  --->
	[*] USB support  --->
                <*>   USB Gadget Support  --->
                      <M>   USB Gadget precomposed configurations
                      <M>     Gadget Zero (DEVELOPMENT)

Example Usage

Ez-Kit target board 

root@adsp-sc589-ezkit:~# modprobe g_zero
zero gadget: Gadget Zero, version: Cinco de Mayo 2008
zero gadget: zero ready
zero gadget: high-speed config #3: source/sink

On the Linux-Host PC

  • Get the testusb

Please following the usbtest to get the testusb.c. and then compile the source code with the command: 

gcc -Wall -g -pthread -o testusb testusb.c
  • run the gadget zero test
usb_gadget_zero.sh
#!/bin/sh
#set -x
lsmod |grep usbtest
sudo modprobe usbtest
lsmod |grep usbtest
sudo cat /sys/kernel/debug/usb/devices | grep -i "Gadget Zero"
lsusb|grep -i "Gadget Zero"|awk '{print $2" "$4}'
 
gadget_bus=$(lsusb|grep -i "Gadget Zero"|awk '{print $2}')
gadget_bus=`echo $gadget_bus | tr -cd "[0-9]"`
gadget_dev=$(lsusb|grep -i "Gadget Zero"|awk '{print $4}')
gadget_dev=`echo $gadget_dev | tr -cd "[0-9]"`
 
do_test()
{
  sudo ./testusb -D /dev/bus/usb/$gadget_bus/$gadget_dev -t${1}
}
 
echo "Gadget zero bulk mode test "
for i in $(seq 1 8)  
do   
do_test $i
done 
do_test 13
 
echo "Gadget zero control mode test "
do_test 9
do_test 10
sudo ./testusb -D /dev/bus/usb/$gadget_bus/$gadget_dev -t14 -c 15000 -s 256 -v 1
  • Test log:
test@madara:~$ sh usb_gadget_zero.sh 
usbtest                36864  0
S:  Product=Gadget Zero
002 023:
Gadget zero bulk mode test 
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 1,    0.126166 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 2,    0.126849 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 3,    0.127574 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 4,    0.125543 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 5,    1.515107 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 6,    0.623720 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 7,    1.528005 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 8,    0.626151 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 13,    2.774978 secs
Gadget zero control mode test 
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 9,    1.920662 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 10,    3.265069 secs
unknown speed	/dev/bus/usb/002/023	0
/dev/bus/usb/002/023 test 14,    3.812687 secs

Go TO USB Interface

resources/tools-software/linuxdsp/docs/linux-kernel-and-drivers/usb/device_mode/gdaget_zero.1594778940.txt.gz · Last modified: 15 Jul 2020 04:09 by cathy fang

Page Tools