Differences

This shows you the differences between two versions of the page.

--- resources:tools-software:crosscore:cces:quick-start [18 Sep 2020 19:24] – [CCES Setup - On-board Debug Agent] Chad Wentworth
+++ resources:tools-software:crosscore:cces:quick-start [01 Oct 2020 18:50] (current) – Chad Wentworth
@@ Line 1: / Line 1: @@
-====== CrossCore Embedded Studio(CCES) Quick Start ======
+====== CrossCore Embedded Studio(CCES) Quick Start for Windows ======
-This page is designed to allow users to quickly get connected to their Analog Devices evaluation boards using CCES.
+This page is designed to show how to quickly get connected to Analog Devices evaluation boards using CCES.
 ==== Hardware Connection Types ====
-There are usually 2 ways that users can connect to evaluation boards. An In Circuit Emulator(ICE), such as the ICE-1000 or ICE-2000 can be used or some ADI evaluation boards support a direct connection to the board using an on-board debug agent. In both cases, the communication between the host PC and the hardware is USB.
+There are usually 2 ways to connect to ADI evaluation boards. An In Circuit Emulator(ICE), such as the ICE-1000 or ICE-2000 can be used or some ADI evaluation boards support a direct connection to the board using an on-board debug agent. In both cases, the communication between the host PC and the hardware is USB.
 <WRAP round 70% tip>
-For information on hardware connections or how to to power up evaluation boards please see the appropriate hardware documentation.
+For information on hardware connections, how to to power up evaluation boards, or switch settings to allow for emulator/debug agent connection, please see the appropriate hardware documentation.
 </WRAP>
@@ Line 18: / Line 18: @@
     - Plug one side of the USB cable into the evaluation board. Plug the other side into a USB port of the PC running CCES.
     - Attach power to the evaluation board unless the evaluation board is USB bus powered.
+The following steps assume that CCES is installed and running on your PC.
 <WRAP round 70% important>
+Connecting the USB cable between the PC and the carrier board prior to installing CCES may result in a failure to find the appropriate Windows drivers.
+</WRAP>
-The following steps assume that CCES is installed and running on your PC.
+  * Navigate to the CCES environment through the Start menu.
+  * Once an application is ready to load to the evaluation board a debug configuration can be created.
+=== Launching the Debug Configuration ===
+Use the **Debug Configurations** wizard to connect to the board. If a debug configuration exists already, select the appropriate configuration and click //Debug//.
+{{:resources:tools-software:crosscore:cces:launch_debug_config.gif?nolink|}}
+<WRAP round 70% important>
+Be sure to select your project in the project explorer so that important details are filled in for you automatically when creating the Debug Configuration.
 </WRAP>
-Connecting the USB cable between the PC and the carrier board or emulator prior to installing CCES may result in a failure to find the appropriate Windows drivers.
+  * To create a debug configuration, choose Run > Debug Configurations
+  * The Debug Configuration dialog box will appear.
+=== Creating a New Debug Configuration ===
+{{:resources:tools-software:crosscore:cces:create_debug_config_da.gif?nolink|}}
+  * Select **Application with CrossCore Debugger** and click the //New// button to create a configuration.
+  * The **Select Processor** page of the Session Wizard appears.
+  * On the **Select Processor** page, ensure the correct processor family is selected.
+  * In //Processor type//, select the processor that matches the processor on the evaluation board. Click //Next//.
+  * On the **Connection Type** page, select //EZ-KIT Lite// for on-board debug agent use.
+  * Choose the on-board debug agent.
+  * Click //Finish// to close the wizard. The new debug configuration is created and added to the Debug Configurations list.
+=== Selecting the Application(s) to Load ===
+{{:resources:tools-software:crosscore:cces:select_application.gif?nolink|}}
+  * In the **Name** edit box, select an appropriate name to describe the configuration, otherwise a default name is provided.
+  * In the **Session** section, choose the program(s) to load (if the appropriate program is not already populated) when connecting to the board.
+  * If not loading any program upon connection to the target, do not make any changes.
+  * Click //Debug// to connect to the target board.
+<WRAP round 70% important>
+While connected to the target, there is no way to choose a program to download. To load a program once connected, terminate the session and then load the new program.
+</WRAP>
+  * To disconnect from the target board, choose //Run > Terminate//.
+  * To delete a configuration, go to the **Debug Configurations** dialog box and select the //Delete// button and choose //Yes// when asked if you wish to delete the selected launch configuration. Then Close the dialog box.
+==== CCES Setup - ICE-1000/ICE-2000 Emulator ====
+Follow these instructions to ensure correct operation of the product software and hardware.
+=== Connect the board to a personal computer (PC) ===
+    - Plug one side of the USB cable into the emulator. Plug the other side into a USB port of the PC running CCES.
+    - Attach power to the evaluation board unless the evaluation board is USB bus powered.
+The following steps assume that CCES is installed and running on your PC.
+<WRAP round 70% important>
+Connecting the USB cable between the PC and the emulator prior to installing CCES may result in a failure to find the appropriate Windows drivers.
+</WRAP>
   * Navigate to the CCES environment through the Start menu.
@@ Line 31: / Line 79: @@
 === Launching the Debug Configuration ===
-Use the Debug Configurations wizard to connect to the board. If a debug configuration exists already, select the appropriate configuration and click Debug.
+Use the **Debug Configurations** wizard to connect to the board. If a debug configuration exists already, select the appropriate configuration and click //Debug//.
 {{:resources:tools-software:crosscore:cces:launch_debug_config.gif?nolink|}}
 <WRAP round 70% important>
 Be sure to select your project in the project explorer so that important details are filled in for you automatically when creating the Debug Configuration.
 </WRAP>
   * To create a debug configuration, choose Run > Debug Configurations
   * The Debug Configuration dialog box will appear.
-{{:resources:tools-software:crosscore:cces:debug_config1.png?nolink&400|}}
-  * Select Application with CrossCore Debugger and click the 'New' button to create a configuration. The Select Processor page of the Session Wizard appears.
-  * Ensure SHARC is selected in Processor family. In Processor type, select ADSP-21569. Click Next. The Select Connection Type page of the Session Wizard appears.
-  * Select Emulator for emulator use or EZ-KIT for on-board debug agent use.
-  * Choose the type of emulator connected or the on-board debug agent depending on the connection type.
-  * Click Finish to close the wizard. The new debug configuration is created and added to the Debug Configurations list.
-  * In the Name edit box, users can select an appropriate name to describe the configuration, otherwise a default name is provided.
-  * In the Session section, choose the program to load (if the appropriate program is not already populated) when connecting to the board.
-  * If not loading any program upon connection to the target, do not make any changes.
-  * While connected to the target, there is no way to choose a program to download. To load a program once connected, terminate the session and then load the new program.
-  * To delete a configuration, go to the Debug Configurations dialog box and select the 'Delete' button and choose **Yes** when asked if you wish to delete the selected launch configuration. Then Close the dialog box.
-  * To disconnect from the target board, choose Run > Terminate.
+=== Creating a New Debug Configuration ===
+{{:resources:tools-software:crosscore:cces:create_debug_config_emu.gif?nolink|}}
+  * Select **Application with CrossCore Debugger** and click the //New// button to create a configuration.
+  * The **Select Processor** page of the Session Wizard appears.
+  * On the **Select Processor** page, ensure the correct processor family is selected.
+  * In //Processor type//, select the processor that matches the processor on the evaluation board. Click //Next//.
+  * On the **Connection Type** page, select //Emulator//.
+  * Choose the type of emulator connected.
+  * Click //Finish// to close the wizard. The new debug configuration is created and added to the Debug Configurations list.
+=== Selecting the Application(s) to Load ===
+{{:resources:tools-software:crosscore:cces:select_application_emu.gif?nolink|}}
+  * In the **Name** edit box, select an appropriate name to describe the configuration, otherwise a default name is provided.
+  * In the **Session** section, choose the program(s) to load (if the appropriate program is not already populated) when connecting to the board.
+  * If not loading any program upon connection to the target, do not make any changes.
+  * Click //Debug// to connect to the target board.
+<WRAP round 70% important>
+While connected to the target, there is no way to choose a program to download. To load a program once connected, terminate the session and then load the new program.
+</WRAP>
+  * To disconnect from the target board, choose //Run > Terminate//.
+  * To delete a configuration, go to the **Debug Configurations** dialog box and select the //Delete// button and choose //Yes// when asked if you wish to delete the selected launch configuration. Then Close the dialog box.

Wiki

Analog Devices Wiki

Differences

Analog Devices Wiki

Differences

Page Tools