Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:circuits-from-the-lab:cn0552 [27 Sep 2022 03:54] – add hw connectors section + grammar edits Trisha Cabildoresources:eval:user-guides:circuits-from-the-lab:cn0552 [22 Nov 2023 09:46] (current) – fix broken link Darius B
Line 65: Line 65:
 | GND      | 2        | | GND      | 2        |
 | IOVDD    | 1        | | IOVDD    | 1        |
 +
 +==== Solder Jumpers ====
 +Eight solder jumpers are available at the bottom of the board, if you want to change the operating modes.  See the schematic for more details. 
 +
 +{{:resources:eval:user-guides:circuits-from-the-lab:cn0552:eval-cn0552-pmdztop-web.png?direct&500|}}
 +^ Description and default connection                                 ^ Solder Jumper    ^ Default Position    ^
 +| ADC SDA connection (pull-up SDA to VDD)                       | P1               | Shorted             |
 +| ADC SCL connection (pull-up SCL to VDD)                       | P7               | Shorted             |
 +| Extended Excitation Enable (connect A1 OUT to P8 pin 3)       | P14              | Shorted             |
 +| ADC REFIN(-) connection (connect GND and P8 pin 5)            | P3               | Open                |
 +| ADC REFIN(+) connection (connect GND and P8 pin 4)            | P9               | Open                |
 +| ADC CIN1(-) connection (connect GND to P8 pin 7)              | P4               | Open                |
 +| ADC CIN1(+) connection (connect GND to P8 pin 8)              | P10              | Open                |
 +| ADC CIN2(-) connection (connect GND to P13 pin 7)             | P5               | Open                |
 +| ADC CIN1(+) connection (connect GND to P13 pin 8)             | P11              | Open               |
 +| ADC VIN(-) connection (connect GND to P13 pin 4)              | P6               | Open                |
 +| ADC VIN(+) connection (connect GND to P13 pin 5)              | P12              | Open                |
 +
 +==== Test Points ====
 +Also, four test points are available to probe the I2C interface.
  
 ===== Device Driver Support ===== ===== Device Driver Support =====
Line 114: Line 134:
 <WRAP round 80% download> <WRAP round 80% download>
 Prebuilt CN0552 Hex File Prebuilt CN0552 Hex File
-  * [[repo>no-OS/releases/download/Latest/cn0552.zip|ADuCM3029_demo_cn0552.hex]]+  * [[repo>no-OS/releases/download/last_commit/cn0552.zip|ADuCM3029_demo_cn0552.hex]]
  
 Complete CN0552 Source Files Complete CN0552 Source Files
Line 154: Line 174:
  
   * **Software**   * **Software**
-    * [[:resources:tools-software:linux-software:embedded_arm_images|Kuiper Images]]+    * [[:resources:tools-software:linux-software:kuiper-linux |Kuiper Images]]
  
 ==== Loading Image on SD Card ==== ==== Loading Image on SD Card ====
  
-In order to control the **EVAL-CN0552-PMDZ** from the Raspberry Pi, you will need to install ADI Kuiper Linux on an SD card. Complete instructions, including where to download the SD card image, how to write it to the SD card, and how to configure the system are provided at **[[:resources:tools-software:linux-software:embedded_arm_images|Kuiper Linux]]**.+In order to control the **EVAL-CN0552-PMDZ** from the Raspberry Pi, you will need to install ADI Kuiper Linux on an SD card. Complete instructions, including where to download the SD card image, how to write it to the SD card, and how to configure the system are provided at **[[:resources:tools-software:linux-software:kuiper-linux |Kuiper Linux]]**. 
 +\\
 \\ \\
 Write the image and follow the system configuration procedure. Write the image and follow the system configuration procedure.
  
 ==== Configuring the SD Card ==== ==== Configuring the SD Card ====
-Follow the Hardware Configuration procedure under **Preparing the Image: Raspberry Pi** in the [[:resources:tools-software:linux-software:embedded_arm_images|Kuiper Images]] page, substituting the following lines in **config.txt**:+Follow the Hardware Configuration procedure under **Preparing the Image: Raspberry Pi** in the [[:resources:tools-software:linux-software:kuiper-linux |Kuiper Images]] page, substituting the following lines in **config.txt**:
  
 <code> <code>
Line 301: Line 322:
   * [[repo>no-OS/wiki|CN0552 No-OS Build Instruction Guide]]   * [[repo>no-OS/wiki|CN0552 No-OS Build Instruction Guide]]
   * [[repo>no-OS/tree/master/projects/cn0552|CN0552 No-OS Device Drivers]]   * [[repo>no-OS/tree/master/projects/cn0552|CN0552 No-OS Device Drivers]]
-  * [[:resources:tools-software:linux-software:embedded_arm_images|Kuiper Linux]]+  * [[:resources:tools-software:linux-software:kuiper-linux |Kuiper Linux]]
      
 =====Registration=====  =====Registration===== 
resources/eval/user-guides/circuits-from-the-lab/cn0552.1664243653.txt.gz · Last modified: 27 Sep 2022 03:54 by Trisha Cabildo

Page Tools