Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:user-guides:circuits-from-the-lab:cn0535:sdp-k1 [16 Jul 2021 08:08] – [Command Summary] John Neeko Garlitosresources:eval:user-guides:circuits-from-the-lab:cn0535:sdp-k1 [27 Oct 2021 08:53] (current) – [SDP-K1] John Neeko Garlitos
Line 34: Line 34:
  
 ==== SDP-K1 ==== ==== SDP-K1 ====
- +>>Shown below is the **CN0535 board** mounted on the **SDP-K1 board** via the Arduino headers. The SDP-K1 only requires a single Standard-A to type-C USB cable to connect to the PC. Both the orange Connected LED and green SYS PWR should light on the SDP-K1 if connected correctly. 
-Shown below is the **CN0535 board** mounted on the **SDP-K1 board** via the Arduino headers. The SDP-K1 only requires a single Standard-A to Mini-B USB cable to connect to the PC. Both the orange Connected LED and green SYS PWR should light on the SDP-K1 if connected correctly. +{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:setup_block_diagram2.png |}} 
- +Note: For SDP-K1 Rev E and Below, a 6V wall-wart power is needed on P15. 
-{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:setup_block_diagram.png |}}+
 ===== Software Setup ===== ===== Software Setup =====
-==== Programming the SDP-K1 ==== 
  
-Following are the steps then required to be completed to set up the [[adi>CN0535|EVAL-CN0535-FMCZ Evaluation Board]] using the **SDP-K1**: 
- 
-  - Download the [[adi>en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/sdp-k1.html#eb-relatedsoftware|SDP USB Drivers]] and run the .exe file. Follow the instructions on the window that appears to install the drives. {{ :resources:eval:user-guides:circuits-from-the-lab:cn0540:sdp-k1_download.png?direct |}} 
-  - Plug the USB cables from the PC into the **SDP-K1**. If installation was successful a new device named SDP-K1 should appear under 'This PC' in Windows File Explorer. {{ :resources:eval:user-guides:circuits-from-the-lab:cn0540:cn0540_sdp-k1pc.png?direct |}} 
-  - Download the AD7768_mbedos.SDP_K1.bin firmware. 
-  - Copy and paste or drag and drop the AD7768_mbedos.SDP_K1.bin file into the SDP-K1 device/folder. This will load the firmware onto the board. 
-  - If the download fails, a FAIL.TXT file will appear on the SDP-K1 device. 
-  - If the download is successful the .bin file will disappear from the SDP-K1 device and there will be no FAIL.TXT file.  
-  - Unplug the **SDP-K1 board** from the PC and plug it back in to hard reset the board and finalize installation. 
 ==== Importing the EVAL-CN0535-FMCZ MBED Example program ==== ==== Importing the EVAL-CN0535-FMCZ MBED Example program ====
  
Line 55: Line 44:
   - After having a acount, open the Example program for EVAL-CN0535-FMCZ https://os.mbed.com/teams/AnalogDevices/code/EVAL-CN0535-FMCZ/   - After having a acount, open the Example program for EVAL-CN0535-FMCZ https://os.mbed.com/teams/AnalogDevices/code/EVAL-CN0535-FMCZ/
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link.png |}}{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link_2.png |}}{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link_3.png |}} {{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link.png |}}{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link_2.png |}}{{ :resources:eval:user-guides:circuits-from-the-lab:cn0535:mbed_link_3.png |}}
 +-
 +
 +
 +
 ==== Connecting to a serial terminal application ==== ==== Connecting to a serial terminal application ====
  
resources/eval/user-guides/circuits-from-the-lab/cn0535/sdp-k1.1626415726.txt.gz · Last modified: 16 Jul 2021 08:08 by John Neeko Garlitos

Page Tools