Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| resources:eval:user-guides:circuits-from-the-lab:cn0419 [26 Feb 2019 08:51] – update Trisha Cabildo | resources:eval:user-guides:circuits-from-the-lab:cn0419 [29 Jul 2021 05:37] (current) – [Registration] Zuedmar Arceo | ||
|---|---|---|---|
| Line 15: | Line 15: | ||
| ===== Required Equipment ===== | ===== Required Equipment ===== | ||
| - | * [[adi>EVAL-CN0419-EBZ|EVAL-CN0419-EBZ Evaluation Board]] | + | * [[adi> |
| * PC with the following //Minimum Requirements// | * PC with the following //Minimum Requirements// | ||
| * PC, Mac, Linux computer, or other host that supports USB | * PC, Mac, Linux computer, or other host that supports USB | ||
| Line 34: | Line 34: | ||
| ==== Speed selection ==== | ==== Speed selection ==== | ||
| - | Peripheral devices run at one of three speeds, low (1.5 Mbps), full (12 Mbps), and high (480 Mbps). The [[adi>EVAL-CN0419-EBZ|EVAL-CN0419-EBZ Evaluation Board]] can accommodate the low and full speed operations. Listed below are some examples of peripheral devices for each speed. | + | Peripheral devices run at one of three speeds, low (1.5 Mbps), full (12 Mbps), and high (480 Mbps). The [[adi> |
| - Low speed devices | - Low speed devices | ||
| * Examples: | * Examples: | ||
| Line 55: | Line 55: | ||
| {{ : | {{ : | ||
| - Set the switch S1 to full speed or low speed operation depending on the peripheral specifications. | - Set the switch S1 to full speed or low speed operation depending on the peripheral specifications. | ||
| - | - Connect the peripheral to J2 of the [[adi>EVAL-CN0419-EBZ|EVAL-CN0419-EBZ]] | + | - Connect the peripheral to P2 of the [[adi> |
| - | - Plug J1 of the [[adi>EVAL-CN0419-EBZ|EVAL-CN0419-EBZ]] into the USB port of the PC/host | + | - Plug P1 of the [[adi> |
| \\ | \\ | ||
| ==== Running the System ==== | ==== Running the System ==== | ||
| - Make sure the setting for S1 is correct based on the peripheral device. | - Make sure the setting for S1 is correct based on the peripheral device. | ||
| - | -Plug J1 of the board into the PC/host, the [[adi>EVAL-CN0419-EBZ|EVAL-CN0419-EBZ]] is automatically turned on and providing isolation. DS1 will light up as an indication that the board is delivering power to the peripheral device. | + | -Plug P1 of the board into the PC/host, the [[adi> |
| -The PC/host must recognize the peripheral connected to make sure the setup is working. | -The PC/host must recognize the peripheral connected to make sure the setup is working. | ||
| -Upon successful connection, you can now provide your peripheral the isolated power! | -Upon successful connection, you can now provide your peripheral the isolated power! | ||
| Line 71: | Line 71: | ||
| * [[ADI> | * [[ADI> | ||
| - | * [[http:// | + | * [[adi>media/ |
| * [[ADI> | * [[ADI> | ||
| * [[ADI> | * [[ADI> | ||
| Line 78: | Line 78: | ||
| <WRAP round 80% download> | <WRAP round 80% download> | ||
| - | [[http:// | + | [[adi>media/ |
| * Schematics | * Schematics | ||
| * PCB Layout | * PCB Layout | ||
| Line 84: | Line 84: | ||
| * Allegro project | * Allegro project | ||
| </ | </ | ||
| + | |||
| + | =====Registration===== | ||
| + | <WRAP round tip 80% > | ||
| + | Receive software update notifications, | ||
| + | </ | ||
| + | |||
| //End of Document// | //End of Document// | ||
resources/eval/user-guides/circuits-from-the-lab/cn0419.1551167482.txt.gz · Last modified: 26 Feb 2019 08:51 by Trisha Cabildo